Can You Back Up with Curt TruTrack 2P Weight Distribution System

Question

Question:

Does this system allow for backing up while turning? Also, how precise is the tongue weight spec? My trailer claims 630lb tw, and I will adding to that load.

asked by: Joe W

0

Expert Reply:

Hey Joe, yes the Curt TruTrack 2P part # C79JR does allow backing up as long as you are backing up mostly in a straight line. If you are going to get close to jackknifing the trailer at all though you would need to remove the springs bars. This is basically how all WD systems are though so this one is no different.

expert reply by: Jameson C

0

Answer 1

The weight capacity on the Curt TruTrack 2P Weight Distribution System #C79JR is controlled by the spring bars used and it will not increase by using a heavier duty ball mount. You will have the same tongue weight capacity of 800-1,000lbs and…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The correct Roadactive kit that fits your 2023 Ford F-150 is the part #RAS3611-YHD. I really like the RAS kits as they basically don't have any downsides. You get the adjustable support, an easy install, no maintenance, and actually improves…

view full answer...

Answer 9

According to RoadActive Suspension the spring rate for the standard kit #RAS3611-S is 2,400 lbs. For the heavy duty #RAS3611-SHD it is 3,600 lbs. The heavy duty #RAS3611-SLHD is the same but only designed to fit if you have factory top overload…

view full answer...

Answer 10

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 11

Hi Steve, I totally understand, as those Pro Pride hitches are great but reaaaaaaaal expensive. So we can get you weight distribution, but due to the size your hitch and weight of your trailer, there will be a cost because there are few options and…

view full answer...

Answer 12

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Can You Back Up with Curt TruTrack 2P Weight Distribution System

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching