Replacement LED Trailer Lights For a 2003 Pace American JT612TA2 Enclosed Trailer
Question:
I have a 2003 Pace American Model JT612TA2 that I want to upgrade to LED lighting for both the turn/tail/stop and clearance marker lights. Do you make a kit for such a conversion? Thank you.
asked by: Steve W
Expert Reply:
Unfortunately Steve, I have no way to see exactly what lights came on your 2003 Pace American JT612TA2. Based on some images I could find it looks like your trailer uses the oval style light like the Optronics # STL72RB which is 6-7/16" long. If yours is a different length please let me know.
For the clearance lights on the fenders they look like the snap in lights like the Amber # AL91AB and Red # AL91RB. The top 3 marker lights look like the # MCL0032RBB. These are the very common 4"x2" lights.
Products Referenced in This Question
Thinline LED Clearance and Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 2-1/2L x 1-3/16W Inch
- Amber
- Optronics
more information >
Thinline LED Clearance and Side Marker Light - Submersible - 3 Diodes - Rectangle - Red
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 2-1/2L x 1-3/16W Inch
- Red
- Optronics
more information >
LED Clearance or Side Marker Trailer Light w/ Reflector - 1 Diode - Black Base - Red Lens
- Trailer Lights
- Clearance Lights
- Reflectors
- Rear Clearance
- Side Marker
- Rectangle
- Surface Mount
- Non-Submersible Lights
- LED Light
- 4L x 2W Inch
- Red
- Optronics
more information >
Product Page this Question was Asked From
Optronics LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 10 Diodes - Red Lens
- Trailer Lights
- Tail Lights
- Stop/Turn/Tail
- Oval
- Recessed Mount
- Submersible Lights
- LED Light
- 6-1/2L x 2W Inch
- Red
- Optronics
more information >
Continue Researching
- Article: Trailer Wiring Diagrams
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Replacement Leaf Spring for 2021 Grand Design Imagine 3250BH
- Q&A: Replacing Peterson PM130 Incandescent Trailer Lights with LED Versions
- Q&A: How to Cut a Grommet Hole for Installation of the Oval Trailer Tail Lights # STL22RB
- Article: Cargo Tie-Down Methods
- Q&A: Replacement Bearings for My 2000 Haulmark Enclosed Trailer
- Q&A: Castle Nut Torque Spec for 7,000 Pound Trailer Axle
- Q&A: Replacement LED Tail Light for Triton Boat Trailer Part # 08478
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: What Gauge Wire does 4-Way Trailer Wiring Use
- Article: Best Boat Trailer Jacks
- Article: How to Choose the Right Trailer Hitch Class
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
Steve W.
4/11/2024
Bud, More info on the lights currently installed on the trailer - Turn/Tail/Stop - Oval shape measuring roughly 6 1/4" x 2 1/8". The lens indicates TruckLite 60, and the rubber grommet holding the lens in says Model 60 TruckLite. Upper Clearance Lights - Rectangle shape measuring 4" x 1 1/4". The two mount holes are spaced 3" apart. Single wire. Fender Clearance Lights - Rectangle shape measuring 2 1/4" x 1". Held into fender by TruckLite Model 15 rubber grommet. Connector on back of light is waterproof 2 pin. If needed, I have pictures of each style of light. Thank you - Steve