Lippert Manual to Electric Landing Gear Conversion Parts
Question:
I have a 2022 Wolfpack 365 toy hauler - I want to add a motor to my front landing gear - I believe I have a lippert landing gear system - Is it possible to buy a Lead rebuilt kit lc146059 and install it in the follower landing gear ? Also are the kits interchangeable with other landing gears manufacture ? Thanks in adavance Jeff
asked by: Jeff M
Expert Reply:
Jeff, it sounds like you have the Lippert Manual Landing Gear Set with Handle # LC333966 and you're wanting to motorize it - In which you can by using your existing gearbox with the Lippert Venture 5th Wheel RV Landing Gear Motor # LC142178 with the switch # LG-145236.
If you are looking for a way to convert your landing gear to a dual motor setup then there's really no way to do that without replacing the follow leg with a lead leg, adding a motor and gear box, adding an additional switch and getting rid of the cross shaft.
For a lead leg you would need part # LC179013, for a gear box # LG-179015 and then motor # LC142178 and switch kit # LG-145236.
Products Referenced in This Question
Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Driver Leg
- Lippert
more information >
Lippert Manual Landing Gear Set with Handle - Weld On - 37" Lift - 6,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 5001 - 6000 lbs
- Landing Gear
- Sidewind Jack
- 37 Inch Lift
- Weld-On
- 2 Jacks
- Lippert
more information >
Replacement Switch for Stromberg Carlson Electric Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Switches
- Stromberg Carlson
more information >
Replacement Aluminum Gearbox for Stromberg Carlson Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Gearbox
- Stromberg Carlson
more information >
Product Page this Question was Asked From
Lippert Venture 5th Wheel RV Landing Gear Motor
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Motor
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Hub And Drum Replacement for 90865 Rockwell Hub and Drum
- Article: Trailer Wiring Diagrams
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: Trailer Maintenance Schedule
- Q&A: Should the Tires Lift Off the Ground While Leveling With the Lippert Ground Control Leveling System
- Q&A: How to Determine if Trailer Axle is Not Aligned and How to Measure to Replace Trailer Axle
- Q&A: How Does Lippert Components Spare Tire Winch with Offset Cable Crank Up and Down
- Q&A: Does Lippert Spare Tire Winch Lock or Hold in Any Position?
- Q&A: How is Lippert Spare Tire Winch LC159056 Raised and Lowered
- Q&A: How Does the Handle Work on the Lippert Components Spare Tire Winch 159056
- Article: Does Solar Panel Type Really Matter?
- Article: How Much Solar Power Do I Need For My RV?
- Article: How to Choose a Bike Rack for a Motor Home or RV
- Article: Best Landing Gear
Bryce D.
3/5/2024
I was wondering if I could convert the following leg to a lead leg by changing the gears on the inside (kit lc146059) - trying to save a few bucks