Replacement Gear Kit for Ram Jack With 12,000 lb Capacity
Question:
i have a ram 10,000 lift 12,000 capacity jack is the parts i need for this jack.
asked by: Glen K
Expert Reply:
The # BD500212 is specifically made for Bulldog jacks. Based on the 12,000 lb capacity and 10,000 lb lift on your Ram jack it sounds like you have a TJD-12000 series jack like the # TJD-12000SP-F2. The correct gear kit would be the # TJD-12000-GR. If you need additional replacement parts we have the following:
-Replacement Sidewind Crank for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs # TJD-12000-HD
-Replacement Handle Shaft for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs # TJD-12000-SHABUS
-Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs # TJD-12000-RSP
-Replacement Bearing for etrailer and Ram Square Jacks - 10,000 lbs # TJD-12000-BR
-Replacement Cap for etrailer and Ram Square, Direct Weld, Sidewind Jack - 10K # TJD-12000-CP
-Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K # TJD-12000-RODNUT
-Replacement Handle Clip for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs # TJD-12000-CLIP
Products Referenced in This Question
Replacement Bearing for etrailer and Ram Square Jacks - 10,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Bearings
- etrailer
more information >
Replacement Handle Clip for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Handle Clip
- etrailer
more information >
Replacement Cap for etrailer and Ram Square, Direct Weld, Sidewind Jack - 10K
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Caps
- etrailer
more information >
Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Gears
- etrailer
more information >
Replacement Sidewind Crank for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Sidewind
- etrailer
more information >
Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Rod
- etrailer
more information >
Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Springs
- etrailer
more information >
Replacement Handle Shaft for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Handle Rod
- etrailer
more information >
Square Direct Weld Jack - Drop Leg w/ Spring Return - Sidewind - 25-7/8" Lift - 10K
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Fifth Wheel Trailer
- Gooseneck Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 9001 - 10000 lbs
- Sidewind Jack
- 26 Inch Lift
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Product Page this Question was Asked From
Replacement Gear Kit for Bulldog Sidewind Jacks w/ 12,000-lb Capacity
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Gears
- Bulldog
more information >
Continue Researching
- Q&A: Does Replacement Gear Kit BD500212 Fit 3-Car Trailer Jack
- Article: Pintle-Hitches
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Article: Trailer Maintenance Schedule
- Article: Best Tire Chains
- Q&A: Instructions for Disassembling a 12,000 lb Bulldog Jack
- Q&A: Replacement Rod and Nut for a Bulldog 12,000 lb Trailer Jack
- Article: How to Measure a Trailer Axle
- Article: Gooseneck to 5th Wheel Adapters
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: How To Use Middle Legs on Lippert Ground Control 3.0 Without Controller
- Q&A: How To Operate Middle Jacks Of A Lippert Ground Control 3.0 Leveling System
- Q&A: Placement of Front and Rear Hangers When Building a Tandem Axle Trailer
- Q&A: Slipper Spring Hanger Positioning for 7,000 lb Tandem Axle