Replacement Cradle and Quick Grip Mount for a Thule Atlantis 1600 Cargo Box

Question

Question:

Will the TH8523387001 replace the cradle for the Quick Grip on the Atlantis 1600? Can I replace just one?

asked by: Dave

1

Helpful Expert Reply:

Yes, the Replacement Cradle for Thule AcuTight Mounting Hardware, # TH8523387001, also fits the Qucik Grip hardware used on your Thule Atlantis 1600 cargo box.

The replacement cradle is sold in quantities of one so yes you can get just one if you only need one. If you also need to replace the Quick Grip then it is # TH05738 for one mount.

expert reply by: Michael H

1

Answer 1

There is a good option for your 2021 Tesla Model Y with the factory roof rack that will allow you to open your rear hatch, and I did verify the fits with the manufacturer for you. The factory rack does have a crossbar spread of 35 inches, and the…

view full answer...

Answer 2

Yes, you can use replacement cradle #TH8523387001 for the Quick Grip mounting system in your Thule Atlantis 2100 cargo box. This cradle works with both the Quick Grip and AcuTight mounting systems in the current and previous generation Thule cargo…

view full answer...

Answer 3

Thanks so much for the photo and the info on your cargo box model. I'm not 100 percent certain which part you are referring to, so I will list all of the available replacement parts for your Thule Atlantis 1600XT cargo box, which I confirmed with…

view full answer...

Answer 4

Yes, you can use replacement cradle #TH8523387001 for the Quick Grip mounting system in your Thule Atlantis 1600 cargo box. This cradle works with both the Quick Grip and AcuTight mounting systems in the current and previous generation Thule cargo…

view full answer...

Answer 5

Sounds like you are looking for the Thule cradle spacer part #TH8523387001 for your Thule Atlantis 1600. This is the spacer that goes between the box and the hardware.

view full answer...

Answer 6

We have replacement mounts like the Replacement Quick Grip Mount Assembly - Thule Ascent, Atlantis, and Force Cargo Box - Qty 1 #TH05738. Without knowing which box you have, I can't give you the specific part you need, however I have linked the…

view full answer...

Answer 7

Though we do not just sell the rubber that slides over the grip we do have the full piece. The Replacement Quick Grip Mount Assembly - Thule Ascent, Atlantis, and Force Cargo Box - Qty 1 #TH05738 comes with everything that you will need and it fits…

view full answer...

Answer 8

Thank you for the picture! So right off I can say that you will need to get more than 1 of the Replacement Cradle #TH8523387001. Since it's a different design than the other 3 I recommend picking up 2 of these and using them for the Quick Grip…

view full answer...

Answer 9

The rubber pieces that are on the claws of the Replacement Quick Grip Mount Assembly #TH05738 aren't available separately so if yours are no longer there and you are wanting to replace them you will need a whole new mount assembly.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Cradle and Quick Grip Mount for a Thule Atlantis 1600 Cargo Box

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching