What Parts are Needed to Add a Wheel to the Redline Trailer Spindle # TRU47FR
Question:
What items / part numbers would I need to add to the following so that I could mount a wheel to this spindle? part number TRU47FR
asked by: Rodney
Expert Reply:
It sounds like you are looking for a hub that matches the TruRyde #84 Trailer Spindle, # TRU47FR. This spindle uses the L44649 outer bearing, L68149 inner bearing, a 10-19 grease seal and fits a 3,500 lb axle, so you actually have a wide range of hubs to choose from. I have attached a link to all of the hubs and hubs/drums that will fit.
When choosing a new or replacement trailer hub, there are a few things to keep in mind. If your trailer does not have brakes, then you will want an idler hub, like the Dexter Trailer Hub, # 84545BX. This is an idler hub with a 5 on 4-1/2 inch bolt pattern (the most common bolt pattern for 3,500 lb axles). If your trailer has electric or hydraulic drum brakes, then you will want a hub/drum assembly like part # 84546UC3, which also has the common 5 on 4-1/2 inch bolt pattern. You will also want to make sure the bolt pattern of the hub matches your wheels. All of our hubs come with the bearings, races, seals and lug nuts, so you would not need to purchase any additional parts other than the wheel and tire.
If you can tell me what type of hub you are looking for, the wheel bolt pattern (see attached help article for help on how to determine your bolt pattern) and the size of your trailer wheels, I would be happy to make a more specific recommendation for you.
Products Referenced in This Question
Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2
- Trailer Hubs and Drums
- Hub
- Standard
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Dexter
more information >
Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Standard
- L68149
- L44649
- For 3500 lbs Axles
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Product Page this Question was Asked From
Square #84 Spindle for 3,500-lb Trailer Axles - 1-1/2" Wide
- Trailer Spindles
- Standard Spindle
- 1-1/2 Inch Diameter
- Square
- For 3500 lb Axle
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Recommended Replacement Grease Seal for 2014 Shorelander Boat Trailer
- Q&A: Trailer Grease Seal to Replace 127194TB
- Article: How to Charge a Dump Trailer Battery
- Q&A: Will the Correct Track Trailer Alignment and Lift Kit Prevent Nose High Towing
- Q&A: How Does the Correct Track Trailer Alignment and Lift Kit Really Work
- Q&A: Does Correct Track Trailer Alignment Kit # RR23QX Come with Enough Brackets for Tandem Trailer
- Q&A: Recommended Replacement For A WFCO WF-8750P Power Center
- Q&A: Is There Down Side to Progressive Dynamics 4000 Series 60 Amp Over 45 Amp
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
- Article: Trailer Hitch Receiver Sizes
- Article: Roadmaster Vehicle Specific Base Plates
- Article: Trailer Maintenance Schedule
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Most Popular Wheel Bearings