Replacement UWS Toolbox Key for a CH501 Lock Core

Question

Question:

Hi CH501 key you sell comes ready to use Thank

asked by: Ram C

0

Expert Reply:

Yes, the Replacement UWS key part # KEYCH501 that you referenced would be the correct replacement key for your UWS toolbox. I can tell by looking at the CH501 that is engraved into your lock core.

expert reply by: Jameson C

0

click to enlarge

Answer 1

In order to determine which replacement key you will need for your UWS Truck Toolbox, you will need to get the code off of the lock core. I have attached a picture for you showing the location. The code should start with CH and followed by 3 numbers.…

view full answer...

Answer 2

You will want the Replacement Key for UWS Toolboxes - CH501 #KEYCH501 and then simply enter the desired quantity.

view full answer...

Answer 3

We have exactly what you need. For a replacement 501CH key for your truck tool box, you will use part #KEYCH501. If you need both the key and lock cylinder, you can use part #UWSLOCKCH501, which comes with the lock core and 2 keys.

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Replacement UWS Toolbox Key for a CH501 Lock Core

Product Page this Question was Asked From

Continue Researching