Grease Seal that Fits Hub/Drum KA90831

Question

Question:

Need seal for trailer brake drum part# KA90831

asked by: Scott

0

Expert Reply:

The correct replacement seal you'd need for a hub/drum KA90831 which is a 3,500 lb axle is the part # 58846.

expert reply by: Jameson C

0

Answer 1

Yes. The KA90831 part number you referenced are a 10" x 2-1/4" drum so the #AKEBRK-35R and #AKEBRK-35L would work well for you. If you wanted to upgrade to a self adjusting brake assembly you could use part #AKEBRK-35-SA. These…

view full answer...

Answer 2

I recommend replacing your Furrion DV5100 with the Jensen RV Stereo, #JWM70A. This requires a cutout of 7-1/2" wide x 2-3/4" tall x 6-1/4" deep for overall installed dimensions of 10-3/8" wide x 3-3/4"…

view full answer...

Answer 3

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Based on what information I could find about AL-KO 8490 hub and drums, it is rated for 3,500 pound axles, has a 5 on 4-1/2 bolt pattern, and is a 10 by 2-1/4 inch drum. If this is the case, we have several options for you. I have attached a link to…

view full answer...

Answer 6

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 7

Yes, the Electric Trailer Brake Kit - Self-Adjusting #AKEBRK-35-SA that you referenced are an exact replacement for the AxleTek assemblies you have now that have Axletek-10-GG stamped on them. If you check out the attached picture you can see the…

view full answer...

Answer 8

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

The best option we have to replace the AV615BHM is the Furrion RV Stereo #DV1230BL. This is also a double din stereo with a DVD player and Bluetooth connectivity; just keep in mind it does require a cutout of 6-15/16" wide x 4" tall x…

view full answer...

Answer 12

I do have a replacement option for your Connex AVS500BT that will have all the features you're looking for with the Jensen RV Stereo w DVD Player #JWM70A, but it would require you to make slight alterations to your cutout hole to fit. This stereo…

view full answer...

Grease Seal that Fits Hub/Drum KA90831

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching