Replacement Light Bar Strip 2016 Northwood Artic Fox Camper w/ Mounting Holes 10-1/8" on Center

Question

Question:

I need to replace several exterior bar lights on my 2016 Northwod Arctic Fox travel trailer. The lights are operated with a switch on the light itself. They have 9 diodes with silver colored cover. The only identification on the light is the following number - 22769-021. Without the cover the light is 11 long. Screw holes are 10 1/8 on center. With the cover the overall length is 11 1/4. The cover has a separate number - 22769-041. 1Can you locate these lights for me?

asked by: David D

0

Expert Reply:

The Opti-Brite LED Strip Light w/ Switch # ILL70CBSBAWN you found appears to be the closest light we have to the dimensions you listed. This light has the same mounting hole screw spacing at 10-1/8" with the overall dimensions being 11-5/16" long, 1-5/8" wide, and 1-1/8" thick. I was unable to find any manufacturer specific information with the parts numbers you listed so the light may have either been custom manufactured for Northwood for your 2016 Arctic Fox. Or the parts are obsolete and the information has been removed from online resources.

expert reply by: Bud M

0

Answer 1

The Valley/Husky 7054 5th wheel trailer hitch fits in industry standard above the bed rails. For a kit that fits both the hitch and your 2001 Chevy Silverado 3500 I recommend Reese custom kit #RP50064-58. This custom kit minimizes the amount of…

view full answer...

Answer 2

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 3

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Answer 8

Since the trailer was off of the ground it would not take much voltage to stop the wheels from spinning so they may be getting power but they may not be getting enough power due to a short or wiring issue. But 9 times out of 10 weak trailer brakes…

view full answer...

Answer 9

I would check the magnets for wear before going on to test them with a meter. If the magnets show abnormal wear or if you can see the windings beginning to show through the friction surface of the magnet then they will need to be replaced. To further…

view full answer...

Answer 10

The Trailer Hub and Drum Assembly part #AKHD-545-35-EZ-K would be an excellent replacement for a Tru-Ryde Hub/Drum RVD-H-545. Then for new brakes, I recommend the Hydraulic Trailer Brake Kit part #AKFBBRK-35.

view full answer...

Replacement Light Bar Strip 2016 Northwood Artic Fox Camper w/ Mounting Holes 10-1/8" on Center

Product Page this Question was Asked From

Continue Researching