Is The Mount For Installing Trailer Tongue Tool Boxes On a V-Nose Trailer Available?

Question

Question:

Do you sell this mount?

asked by: Raymond

0

Expert Reply:

You will need to have a custom mount fabricated for installing 2 of the DeeZee Specialty Series Trailer Tongue Tool Boxes # DZ91717P. As not all V-Nose trailers are going to have the same dimensions and the frames can also have different positions the mounts need to be custom fabricated. I have seen some use a steel plate mounted on top of the frame while others use angle iron welded to the frame to provide the support and mounting points for the boxes.

expert reply by: Bud M

0

A-Frame Trailer With 2 A-Frame Tool Storage Boxes
(click to enlarge)

Answer 1

To find the correct E-Z Flex Equalizer, you will need to take off your current ones and measure the distance from the center of the one end hole to the center of the other. You will also need to ensure that your leaf springs are 1-3/4" wide.…

view full answer...

Answer 2

We have seen people mount storage boxes on either side of the nose of a V-nose trailer like what you see in the picture I attached. The part #DZ91717P would work well if you have room for it like that. The dimensions of the box are 36" long…

view full answer...

Answer 3

Most roof vents follow the standard size opening. That size is 14-1/4 inches by 14x1/4 inches but it is most commonly referred to as 14 x14. Many different vents on the inside and outside flanges can have different measurements to gain a certain look…

view full answer...

Answer 4

When choosing the slider you want to measure the outside front of box width including the flange. Then you need to select a slider that extends a minimum of 2-1/2 inches beyond each side of the box width. For example, the Black Solera Slider…

view full answer...

Answer 5

For your 2003 Chevy Silverado BullRing has the BullRing Retractable Tie-Down Anchors for Truck Bed Stake Pockets - Raised Fit - 1,000lbs - Qty 4 #BU85FR or the #BU25FR for a quantity of 6. For your 2019 Ram Bullring has a stainless steel flush-fit…

view full answer...

Answer 6

Depending on the length of your crossbars and the width of your bed yes, there is a way to mount the Yakima OutPost HD ladder rack system on your utility trailer. What you're going to need are the Yakima HD Tracks, like the 60" #Y74MR, along…

view full answer...

Answer 7

Looking at the BAL Retract-A-Spare it has a much different design than the Lippert Spare Tire Winch #LC159056 you found. You may be able to mount the new winch so it will still work on your trailer but as we do not have both the products here with…

view full answer...

Answer 8

The UWS A-Frame Trailer Toolbox #UWS01039 measures 18" wide on the outside so if you use the larger Ego batteries that give you the 18" this won't be wide enough and you'll need to use a different box like the DeeZee Specialty…

view full answer...

Answer 9

These toolboxes do not contain mounting hardware due to the different construction and mounting locations that may be required for many different styles of trailers. A lot of how you install the UWS A-Frame Trailer Toolbox #UWS01065 depends on where…

view full answer...

Answer 10

The Buyers Products Utility Storage Box, #3371712250 has a top of box measurement of 51" x 19-1/2" with a height of 22-1/2". The base being 46.5" x 15.5". Please note the attached image.

view full answer...

Answer 11

Yes, we do have a roof rack that will work with the rounded roof on your Interstate cargo trailer. It is the Rack'Em Fitz-All Enclosed Trailer Ladder Rack item #RA-28. This roof rack has a 400 lbs capacity and mounts to the side of your trailer…

view full answer...

Is The Mount For Installing Trailer Tongue Tool Boxes On a V-Nose Trailer Available?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching