Replacement Bearing Kit for a 2018 Keystone Montana High Country 305RL With 7K Axles

Question

Question:

2018 305rl fifth wheel with 7000lb dexter axles what bearing and greese seals fit

asked by: Donald

1

Helpful Expert Reply:

Thanks for the photo!

You need the Replacement Bearing Kit # BK3-200 for the 7K axles on your 2018 Keystone Montana High Country 305RL 5th wheel trailer. I confirmed this with my contact from Dexter Axle.

expert reply by: Jon G

1

Axle Tag on 2018 Keystone Montana High Country 305RL
(click to enlarge)

Answer 1

For 7k Dexter axle bearings you have two options depending on the inner diameter of the seal you need. You would need part #BK3-200 for if your seal has an inner diameter of 2.25 inches. Or part #BK3-210 for if your seal inner diameter is 2.125…

view full answer...

Answer 2

The correct bearing and seal kit for your Dexter 7,000 lb axles is going to be either the Bearing Kit part #BK3-210 which has a 2.125" seal or the Bearing Kit part #BK3-200 which has a 2.250" seal. Unfortunately, this axle could have come…

view full answer...

Answer 3

In order to determine the correct replacement bearings and seals for your older 6,500 lb - 7,200 lb axles you'll need to pull the hub and look for part numbers on the bearings/seals and/or measure the spindle at the different places where the…

view full answer...

Answer 4

Thanks for sending in the picture of your axle label. Based on that I know that the correct bearing kit is the #BK3-200 which comes with bearings and a seal for a 7k hub.

view full answer...

Answer 5

Based on my research, the 023-326-00 number you found at the back of your existing brake assemblies refers to the Dexter 12 inch x 2 inch electric brake assembly that is designed for 6,000 pound axles and features a 5 bolt mounting flange pattern. If…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 11

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...

Answer 12

Hey Doug, thanks for reaching out! The MORryde ALLTREK 4000 #MR89DR dimensions can be a bit difficult to explain via text so I've attached an image giving you the dimensions you're asking about!

view full answer...

Replacement Bearing Kit for a 2018 Keystone Montana High Country 305RL With 7K Axles

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching