Could B and W Continuum Weight Distribution System be Used with Boat Trailer

Question

Question:

does this BW weight continuum work on a boat trailer set up?

asked by: Moses

0

Expert Reply:

If the boat trailer was an a-frame style without surge brakes and not a pole tongue style yes the B and W Continuum weight distribution system part # BW78FR would fit and work great.

expert reply by: Jameson C

0

Answer 1

4,500 lbs to 7,500 lbs is a pretty wide range of weight. Tongue weight is typically 10% - 15% of your trailer's total weight and in your case that's 450 lbs - 1,050 lbs. The B&W Continuum Weight Distribution System w/ Sway…

view full answer...

Answer 2

To be completely honest the sway control feature of the B and W Continuum part #BW78FR isn't nearly as advanced as the rest of the system. The advertised sway control of this system is in the head of the system between where the ball and the…

view full answer...

Answer 3

Yes, the B&W Continuum Weight Distribution System #BW78FR can be installed as easily on your angled driveway as it can be on level ground.

view full answer...

Answer 4

Jameson is correct - on a tandem axle trailer you want brakes such as the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3.5K #23-468-469 on the axle that bears the most weight, and in the large majority…

view full answer...

Answer 5

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 6

In some situations, brakes can be installed on only one axle of a tandem axle trailer, however you should first check your state laws to see how many brakes are required for the gross vehicle weight rating (GVWR) of your tandem axle trailer. Some…

view full answer...

Answer 7

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 10

The B&W Continuum #BW78FR and the Reese Strait-Line #RP66083 are both great systems. The B&W Continuum is going to be easier to set up, but as far as sway control goes, I definitely have to give the edge to the Reese Strait-Line. The…

view full answer...

Answer 11

Hey Tom, you are on the right track. I checked out your 2023 Jayco Jay Flight 284 BHS and it does have an underslung coupler so the correct B and W Continuum weight distribution would be the part #BW88FR. An underslung coupler is basically one that…

view full answer...

Answer 12

Weight distribution works to distribute the tongue weight of a trailer up to the front axle of the tow vehicle so that it will sit more level and handle/brake better. That being said the systems do not "reduce" tongue weight or allow you to…

view full answer...

Could B and W Continuum Weight Distribution System be Used with Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching