Is the RoadActive Suspension Custom Leaf Spring Enhancement Kit Compatible w/ Bump Stops?

Question

Question:

Are ras suspension compatible with bump stops

asked by: John A

1

Helpful Expert Reply:

Yes, they are. The RoadActive Suspension Custom Leaf Spring Enhancement Kit item # RAS3611-HD you were looking at, is confirmed to fit a 2018 Chevrolet Silverado 2500 and are compatible with bump stops.

expert reply by: Jerred H

1

Answer 1

No, it will not. The correct Draw-Tite Hitch for your 2018 Jeep Wrangler JK Unlimited Sport is item #DT78MR. This hitch is custom fit and will bolt to your Jeep's standard bumper with included hardware. I have linked an installation video…

view full answer...

Answer 2

Yes, it can if you have the all wheel drive model. The rear wheel drive models will have to be put on a trailer. To flat tow your 2022 Dodge Durango you will need the following parts: Tow Bar and Safety Chains - Roadmaster Falcon 2 Tow Bar item…

view full answer...

Answer 3

We actually got a chance to test out a few of our cargo bags, including the Curt #C18211 just the other day. The bag itself measures 56" long x 22" wide x 21" tall. We found it to be extremely roomy we were able to fit about 5 duffel…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Is the RoadActive Suspension Custom Leaf Spring Enhancement Kit Compatible w/ Bump Stops?

Product Page this Question was Asked From

Continue Researching