What are the Dimensions of the Curt Clevis Hook with Spring Loaded Safety Latch

Question

Question:

I need to know if this hook will fit in My Reese Elite Series bed tie downs. What is the thickness of the hook?

asked by: Jason

0

Expert Reply:

The Curt Clevis Hook # C81970 is not completely uniform so its measurements vary depending on where it is being measured. I have included a video on this page that shows the width and thickness at key points and the opening dimensions. The opening is listed by the manufacturer at approximately 1-1/3 inches.

expert reply by: Michael H

0

Answer 1

For a general-purpose safety chain for a standard gooseneck trailer we offer #337BSC3842 from Buyers Products. This is a 42-inch chain with 3/8-inch clevis. The chain is rated for 15,000 pounds. This is sold as a single chain, not a pair. The 36-inch…

view full answer...

Answer 2

I have a clevis hook that may work. Take a look at part #6495-401-04 . This hook has a working load limit up to 5,400 lbs and the pin that connects through the chain is 7/16 of an inch in diameter. The Curt Clevis Hook, #C81970 , has a 40,000 lb…

view full answer...

Answer 3

A safety chain's working load limit (WLL) is always 1/3 of the chain's break strength and it is the limit you want to stay within in normal use. If your chains have a rated break strength of 11,700-lbs then the correct clevis slip hook you…

view full answer...

Answer 4

The Curt Clevis Hook with Spring Loaded Safety Latch - 7/16 - 40,000 lbs Item #C81970 that you referenced is Grade 70, the attachment pin is 1/2 inch diameter, and the opening where the chain would slip through and the pin would hold it in place…

view full answer...

Answer 5

The Curt Clevis Hook with Spring Loaded Safety Latch - 7/16" - 40,000 lbs #C81970 will work with most systems. Without knowing the hitch or the diameter of the safety loops, I can't confirm a fit other than to tell you the opening of the…

view full answer...

Answer 6

The Curt 81960 clevis hooks you referenced have a 1" opening, and the safety chain loops of Curt hitch #C15802 are approximately 1-1/8" wide so you would be able to use them, but the hooks would not quite close. For Curt clevis hooks with a…

view full answer...

Answer 7

I have a clevis hook that may work with your 5,000 lb trailer. Take a look at part #6495-401-04. This hook has a working load limit up to 5,400 lbs and the pin that connects through the chain is 7/16 of an inch in diameter. We have heavy-duty clevis…

view full answer...

Answer 8

The Curt safety chain loops are notorious for being hard to fit safety chains to since they are pretty wide. Your best and easiest solution will be to replace the clevis hooks of your current safety chains with the part #C81970 which will easily fit…

view full answer...

Answer 9

Your best and easiest solution will be to replace the clevis hooks of your current safety chains with the part #C81970 which will easily fit the safety chain loops of the Curt ball and safety chain kit part #C60692 that you referenced.

view full answer...

Answer 10

On the hook end of clevis hook #C81970 the opening is approximately 1-1/8 inches wide. The end with the pin it that you would attach to a rope or chain measures 5/8 inches wide.

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

What are the Dimensions of the Curt Clevis Hook with Spring Loaded Safety Latch

Product Page this Question was Asked From

Continue Researching