Availability of Trailer Hitch Receiver for Towing with 2008 Chrysler Sebring Hard-Top Convertible
Question:
Can I put a trailer hitch on my 2008 hard top convertible Chrysler Sebring? We would be towing.
asked by: Brant
Expert Reply:
We do offer two light-duty Class I trailer hitch receivers for the 2008 Sebring hard-top convertible and both can be seen on the link provided. The hitch # 36448 that you referenced is not a fit for your convertible, only for the sedan version of the Sebring.
The correct Draw-Tite hitch is # 24871. I have linked an installation video for your reference as well as the written instructions.
Please note that according to a Chrysler Corporation document I located online not all versions of the Sebring convertible are rated for towing. The 2.7L V6 Touring model and the 3.5L V6 Limited both have a tow rating of 1000-lbs. The LX version with its 2.4L engine is not recommended for towing.
When different components in a system (in this case the vehicle and hitch) have different ratings, then the lowest-rated item determines the overall limit for the combined system. Even though the Class I hitches we offer for your Sebring convertible are rated with a 2000-lb towing capacity, the vehicles capacity becomes your towing limit. If you have one of the tow-rated versions of the Sebring, then your working tow limit is 1000-lbs.
You will also need a ball mount, hitch ball, pin and clip and a wiring harness for your vehicle. You can use
part # 3593, which includes the ball mount, pin and clip. For a wiring harness to connect to your trailer you can use part # 118444 also from Draw-Tite. For a 1-7/8-inch hitch ball you can use # 19256. If you need a 2-inch hitch ball you can use # A-82.
I have linked two articles on towing basics that may be useful to you.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >