Recommended Replacement Thule Lock Cylinders for a 2016 Mazda CX-5

Question

Question:

I need 4 Thule N212 lock cylinders but not 4 keys. Are you able to make a 4 pack of the N212 cylinders available ?

asked by: Farrah D

0

Expert Reply:

The Replacement Lock Cylinder and Premium Key for Thule One-Key Systems # TH52DD is not sold in packs of 4 so since you need 4, you'd need to purchase 4 separately.

Or, you can use the Thule One-Key System Lock Cylinders # TH450400 which is a pack of 4 but it'll replace all of your lock cylinders with 4 brand new locks and won't be related to the N212 key you have.

Both options will be about the same cost so it'd be entirely up to you what you choose, but I'd just stick with the 4 individual locks so I could keep using the same keys.

expert reply by: Bryce D

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

Hello again Mark. I checked with Curt and the USCAR #C56229 uses 14 gauge wire for every wire but the 12v line. The 12v line is 12 gauge.

view full answer...

Answer 5

The 7-Way Super Sealed Connector #50-87-004 uses 14 gauge wires for lighting(yellow, green, brown and red) 10 gauge wire for power(white and black) and 12 gauge wiring for the brakes(blue) . We also have this harness available in a 7' length…

view full answer...

Answer 6

If your 2016 Mazda CX-5 was made on May, 16th 2016 then you have a 2016.5 mid-year model as the cutoff date for prior mid-year models was April 1st, 2016. However, none of that matters when choosing a trailer hitch for your CX-5 as the Curt Trailer…

view full answer...

Answer 7

I don't have a whole lot of information for you but I spoke with Thule and they informed me that the lock core will need to come out first (with change key part #853-1251) and then the lock shield part #05771 can be removed. The lock shield…

view full answer...

Answer 8

I will need a little more background information if possible. Were you driving through wet/rainy/snowy conditions? If so what was the approximate outside temperature? I have seen new or used cargo boxes, not just the Thule Force XT L #TH6357B, but…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Recommended Replacement Thule Lock Cylinders for a 2016 Mazda CX-5

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching