Driver and Passenger Side Optronics LED Trailer Combination Tail Lights

Question

Question:

Hi. Is there a driver side light that matches this stl38rb? If so what would be the part number? Thank you!

asked by: Jean

0

Expert Reply:

Yes, we do have both the driver and passenger side tail lights for the part number you're asking about:

- Driver Side # STL39RB
- Passenger Side # STL38RB

I'm attaching a review and installation video for you to check out!

expert reply by: Jon G

0

Answer 1

Since you don't want a license plate light or bracket what you'd want is two of the part #STL38RB for both sides of your trailer. For a couple amber LED clearance lights you could then use the part #MCL36AB and for a wiring harness part…

view full answer...

Answer 2

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 3

The two bearings you mentioned have different inner diameters. The #L44643 has an inner diameter that is exactly 1 inch and the #L44649 is 1.06 inch. This may not seem like a lot but it's a big enough difference to prevent the hub you have now…

view full answer...

Answer 4

We do not, but as long as the new lug hubs use the same bearings as the current hubs you can just swap them out. For instance, if your current hubs used the L44643 bearing you can use both the Trailer Idler Hub Assembly for 2,000-lb Axles…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Driver and Passenger Side Optronics LED Trailer Combination Tail Lights

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching