Is It Normal To Have A Small Gap Between The Flange And The Frame On The e45ZR?
Question:
I installed the E45ZR hitch on my 2023 Telluride and ended up with a 1/8inch gap between the hitch and the frame of my car at one bolt-through mounting location. Is this safe to use as long as the bolt and nut are tightened to the specified torque?
asked by: Dan
Expert Reply:
While ideally, the flange would be flush against the frame, this does not look like anything out of the ordinary. These hitches are made of a mild flex steel and are designed to bend. Looking at the structure of this hitch, it is likely that we do have a very slight bend somewhere. If you were able to get the bolts torqued to spec, this will be fine to use. If you do want to remove the hitch and correct the bend, it is very easy to do. I have included a link below to our guide on correcting a "flexed' hitch.
That said, this may not be necessary in this case. The bend is so minor I do not see this effecting functionality in any way.
Products Referenced in This Question
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Concealed Cross Tube
- etrailer
more information >
Product Page this Question was Asked From
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Concealed Cross Tube
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Curt Trailer Hitch Receiver Installation - 2024 Kia Telluride
- Q&A: Is Trimming Required to Insall the etrailer Hitch e45ZR on a 2024 Kia Telluride?
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: etrailer Class III Trailer Hitch Installation - 2024 Kia Telluride
- Shop: Trailer Wiring
- Article: My Trailer Hitch Doesn't Fit
- Shop: Roof Rack
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: etrailer Class III Trailer Hitch Installation - 2020 Kia Telluride
- Q&A: Recommended Wiring Harness for a 2023 Kia Telluride
- Video: etrailer Class III Trailer Hitch Installation - 2023 Kia Telluride
- Video: Malone Kayak Hammock Hoist System Review
- Video: Choosing the Right Trailer Wiring
- Shop: WeatherTech Mud Flaps - Easy-Install, No-Drill, Digital Fit - Front and Rear Set
- Shop: Malone Kayak Hanger for 2 Kayaks - Wall or Ceiling Mount - 135 lbs
- Shop: Malone Kayak Hoist - 120 lbs
- Q&A: Best Roof Rack for 2020 Kia Telluride With Naked Roof and How Does It Attach
- Shop: Floor Mats
- Shop: Mud Flaps
- Shop: Windshield Covers
- Search Results: y28tr
- Search Results: y00426
- Search Results: hitch receiver riser
- Search Results: hitch
- Search Results: roof rack
- Shop: Rhino-Rack Vortex Aero Crossbars - Aluminum - Black - 54" Long - Qty 2
- Search Results: trailer hitch
- Q&A: Trailer Wiring Harness For 2023 Kia Telluride XLine