Information Needed To Find Replacement Wheel Stud For Axletek Trailer Hub

Question

Question:

I am looking for a lug nut wheel stud for a Axletek. I work at General rv. I have photos if needed

asked by: Samantha B

0

Expert Reply:

To verify we have the correct wheel stud I will need for you to remove one of the studs and measure the length of a good stud, thread diameter and pitch, length of knurled section and diameter of the hole it fits into. This information will ensure we find the correct part.

expert reply by: Bud M

0

Answer 1

I recommend the Electric Trailer Brake Kit #AKEBRK-7-D. The dacromet-coated backing plates are corrosion resistant which is ideal for a boat trailer. Both left and right hand sides are included with the kit. The Trailer Hub and Drum Assembly…

view full answer...

Answer 2

Yes, the Lippert High-Speed Power Stabilizer Jack part #LC298707 is a direct replacement for the OEM LCI Model 161453 Rear Stabilizer Jack. The Lippert High-Speed Power Stabilizer Jack part #LC369774 comes with a white switch instead of black. All of…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Information Needed To Find Replacement Wheel Stud For Axletek Trailer Hub

Product Page this Question was Asked From

Continue Researching