How Much Does the Replacement Ramp for etrailer Aluminum Motorcycle Carriers Weigh?

Question

Question:

What is the weight of this ramp and the length of it ?

asked by: Dale E

0

Expert Reply:

The Replacement Ramp for etrailer Aluminum Motorcycle Carriers item # e92TR weighs 5 lbs and measures 41" long.

expert reply by: Jerred H

0

Answer 1

So even though your Yakima SkyBox 18 #Y07336 or SkyBox21 #Y07337 has the diamond shaped hinges currently, those are an older model hinge that is no longer used by Yakima; you also won't be able to use the Replacement Front Lid Support 8870090…

view full answer...

Answer 2

I would try some lubricant like WD40 to clean the lock. Make sure to get the lubricant inside the lock. You can often slide the key in the keyhole to work the lubricate into the lock mechanism. If you can't get it to work still you may need to…

view full answer...

Answer 3

I did some searching around on the internet and came up with a few interesting tips to prevent rodents from eating vehicle/trailer wiring. Here is what I found: Noise will keep the rodent's away. So a portable radio would work for this. Flashing…

view full answer...

Answer 4

The way the Curt Trailer Hitch, #13703, mounts to an I-Beam frame is that the top bracket on either side of the hitch attaches to the middle, vertical part of the frame. It sounds as if at that point you have 74 inches. If that is the case then this…

view full answer...

Answer 5

The main tube on Curt trailer hitch #13703 measure 2-5/8 inches square on the outside. The wall thickness is 1/4 inch. The overall length is 68-1/2 inches. On the brackets, measuring from the center of the main tube to the nearest end of the bracket…

view full answer...

Answer 6

If it was a 4-pin connector with 5 wires then it is called a wishbone harness and would have 2 wires attached to the running light pin so you have one wire for each side of the trailer. Typically, on a 4-Way, the white wire is ground, brown is…

view full answer...

Answer 7

My suggestion is to test the wires for function with the trailer connected to the tow vehicle. You will need a circuit tester, like part #PTW2993 and a 12v power source, like a car battery. You can then probe the connector with the tester to…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

You will need to use a hitch mounted motorcycle carrier like the Ultra-Fab #UF48-979033 to carry your Honda Trail 125. This is required due to the weight of the Honda at roughly 250lbs. A bumper mounted rack like the Swagman #S64663 is only rated for…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

How Much Does the Replacement Ramp for etrailer Aluminum Motorcycle Carriers Weigh?

Product Page this Question was Asked From

Continue Researching