Determining The Correct Replacement Wheel Center Cap for a 2021 Venture Sonic Lite TT

Question

Question:

I have a 2021 Venture RV Sonic Lite SL-169VMK travel trailer with the stock 15” wheels. I am trying to find a replacement wheel center cap plug only. The I.D. of the he hole is approximately 2.44” and the O.D. of the flange is 2.87”. I cannot find those measurements in your website. I only see multiple listings for center plugs that fits a 2.0” diameter hole. Please advise. Thank you.

asked by: Steve C

0

Expert Reply:

I checked to see if we have anything that matches what you're looking for, however I was not able to find anything that matches.

The closest I was able to find to what you're looking for is the Snap-In Plug for Lionshead Trailer Wheel Center Caps # LHSI60C which has an O.D of 2.25" ( 2-1/4").

What would really help determine if we have something that'll work for you is to know what wheel you're trying to replace the center cap for. Most of these are interchangeable relatively speaking, but knowing what wheel you're needing a center cap for would help.

expert reply by: Bryce D

0

Answer 1

We do have a snap in plug for Lionshead trailer wheel center caps. The Snap-In Plug for Lionshead Trailer Wheel Center Caps - Chrome #LHSI60C will fit the following three models. #LHCS102, #LHCS108, #LHCS109. If you have one of these models then this…

view full answer...

Answer 2

To pick out a replacement grease seal you will need to measure the diameter of the spindle where the grease seal rides with a digital or dial caliper and then need to measure the hub bore where the current seal rides. With those two dimensions we can…

view full answer...

Answer 3

The Snap-In Plug #LHSI60C that you referenced is indeed designed to fit certain Lionshead Center Caps but it will still work as a replacement on other brand caps as long as the dimensions match. The best way to determine if this will fit your…

view full answer...

Answer 4

You will want to use a dial caliper or micrometer to measure the inner diameter of the hub you have on your trailer to determine what size cap would be needed. Check out the picture I attached that shows this measurement being taken on a hub. I…

view full answer...

Answer 5

From the numbers you provided it sounds like you need replacement grease seals. In my research, the grease seals I found with the GS-1719DL number have a 1.72 inside diameter and 2.565 outside diameter. The replacement double lip grease seals you…

view full answer...

Answer 6

You can check the condition of your hub's races by carefully removing all bearing grease with a rag to expose the actual surface of the races. When they are completely free of grease, etc., inspect them for any signs of scoring (very slight…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Determining The Correct Replacement Wheel Center Cap for a 2021 Venture Sonic Lite TT

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching