What is The Distance Between The Mounting Studs On The Electric Brake Kit # AKEBRK-35-SA?

Question

Question:

What is the distance on the studs on the mounting flange

asked by: Seve

0

Expert Reply:

The studs on the Electric Brake Kit # AKEBRK-35-SA are separated 2-13/16" on center vertically and horizontally. I have included an image below showing the measurement points. These attach using the Mounting Hardware # BRKH10B.

expert reply by: Bud M

0

Mounting Bolt Pattern
(click to enlarge)

Answer 1

What you have is an 86" long axle with a 4,400 lb capacity. Since 4,400 lb axles are no longer being produced, you will need an axle with a higher capacity for a replacement. I recommend the Trailer Axle Beam with Easy Grease Spindles #e45GR.…

view full answer...

Answer 2

The Electric Trailer Brake Kit part #AKEBRK-7-SA does not come with the hub/drum. In order to find the correct hub/drums we are going to need to know your bearing numbers or measurements. We would also need to know the bolt pattern of your wheels. I…

view full answer...

Answer 3

Actually, there's a little more to it than that. The magnets on the #K23-478-479 are a little different, but the primary difference is the mounting bolt pattern. On a typical 3500 lb brake assembly, the mounting studs will all be 2-7/8 inches…

view full answer...

Answer 4

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 5

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Yes, the Electric Trailer Brake Kit - Self-Adjusting #AKEBRK-35-SA that you referenced are an exact replacement for the AxleTek assemblies you have now that have Axletek-10-GG stamped on them. If you check out the attached picture you can see the…

view full answer...

Answer 8

Based on what information I could find about AL-KO 8490 hub and drums, it is rated for 3,500 pound axles, has a 5 on 4-1/2 bolt pattern, and is a 10 by 2-1/4 inch drum. If this is the case, we have several options for you. I have attached a link to…

view full answer...

Answer 9

Hey Sam, so from previous customers we have determined that the Sure Trac axles use the standard trailer axle components so yes the brake assemblies part #AKEBRK-35-SA and the hub part #AKHD-545-35-K would fit and work great.

view full answer...

Answer 10

Hey Roy, The only U-bolt kit we currently only offer for 1-1/2" square axles is part #CE23102, which only has a 3-3/8" length so it likely wouldn't be the best option for you. Instead you'll want to order the 1-1/2" Square…

view full answer...

Answer 11

The mounting flange bolts of the #AKEBRK-35-SA use the standard 4 bolt pattern seen on axles rated for 3,500 lbs. The picture I attached shows the distance between all of the studs.

view full answer...

What is The Distance Between The Mounting Studs On The Electric Brake Kit # AKEBRK-35-SA?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching