How to Pick Out Slide Topper that Fits 2021 Micro Minnie 2108TB

Question

Question:

2021 micro minnie 2108tb. what slide out topper do i need?

asked by: Fale

0

Expert Reply:

We don't have a way to know what slide topper is correct for your 2021 Micro Minnie 2108TB but we can help you determine what you'd need. You'd need to measure the width of your slide out including the flange and with that dimensions you can pick out the correct fit. If you follow the attached link on this page you'll see all of the slide toppers we carry and from there you can select the width you see on the filters and the correct fitting slide toppers will be listed.

expert reply by: Jameson C

0

Answer 1

You're correct that you need to measure from the outside edge to outside edge of the flanges. If your measurement from flange to flange is 82.25" then you're going to want the Solera RV Slide-Out Awning - 7'1" Wide - 48"…

view full answer...

Answer 2

There is not a 25"-30" model of the Lift Assist available, but it sounds like you probably have the SolidStep Manual Fold-Down Steps for 26" Wide RV Door Frames - Quadruple - Aluminum #LC678025 on your coach, and there is a process…

view full answer...

Answer 3

There are two different SolidStep Lift Assist Kits, part #LC733937 and part #LC733939. In order to confirm either of these will work for you, you will need to go though the purchase verification process outlined by Lippert. See Below: The Lift Assist…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

For your 2018 Ram 2500 with the factory puck system the best 5th Wheel Hitch is the B&W OEM Companion. If you have the 8 foot bed then you will want the fixed 25K #BWRVK3600 and if you have the short 6-1/2 foot bed you will need the 20K Slider…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 8

Sorry Jennifer, I am a bit confused as you were looking at the Replacement U-Clamp Bracket #RM-B141 which mounts with bolts and not U-bolts. This part works with the Split Bushing #RM-205217-10 for the discontinued Roadmaster Front Anti-Sway Bar…

view full answer...

Answer 9

Brien, it sounds like you did your research so kudos to you, but the awning you're looking at is not going to work with the wind sensor. You'd need to use the Solera Smart Arm 12V Power RV Awning #LC517517 instead. You're also going to…

view full answer...

Answer 10

Hi Joe, The Blue Ox Base Plate Kit #BX1139 is a confirmed fit for your 2024 Jeep Wrangler Rubicon X per Blue Ox. I don't currently have an installation video on a model with a steel bumper but I did measure from the mounting holes down to the…

view full answer...

Answer 11

The Voyager WiSight Wireless RV Backup Camera System #ASA37YR you were looking at is only compatible with the RV Backup Camera #ASA74YRor #WVH100 so this would need to be the camera you already have installed or you would need to replace the camera.…

view full answer...