Will Yakima Mighty Mount 23H Accessory Adapter Fit Factory Crossbars on a 2022 Toyota Sienna

Question

Question:

I have a Toyota Sienna 2022 with factory roof racks. Would like to install the Yakima MightyMount 23H adapter to fit a tandem bike carrier we have. Approximate dimensions of the roof rack cross bar is 2.6 inch wide x 0.8 inch thick. Do you think this would work?

asked by: Charles L

0

Expert Reply:

Yes, the Yakima Mighty Mount 23H Accessory Adapter # Y03523 will work great for the factory crossbars on your 2022 Toyota Sienna.

expert reply by: Jon G

0

Answer 1

I spoke with my contact at Yakima and he informed me that the real holding power of this rack is coming from the downtube clamp. Step 27 of the install instructions refers to this. If the wheel is loose in the tray you’ll want to slid the strap until…

view full answer...

Answer 2

Yes, the Batwing Awning #RR33100 (Driver's Side) or #RR33200 (Passenger's Side) can be mounted to your Yakima JetStream crossbars so long as they extend out past your roof rack's feet. They have mounting brackets which install inside the…

view full answer...

Answer 3

Rhino Rack offers the RT-Style Roof Rack Track that would mount directly to the roof of your 2008 Ford Ranger with pop rivets. You will need a rivet gun to install this track so if you do not have one already, you could purchase one from a local…

view full answer...

Answer 4

The dimension you are looking for on the #RR31102 is 1-1/2".

view full answer...

Answer 5

The Rhino-Rack Heavy-Duty 50-Inch Roof Rack Crossbar #RB1250S has cross-section dimensions of 1-7/8-inches tall and 1-5/8-inches wide, as shown in the photo I prepared for you. We also offer two bars as a set #RB1250. The vehicle known as the…

view full answer...

Answer 6

Yes, we do have foam pads that will fit around your Rhino-Rack Heavy-Duty Roof Rack Crossbars #RB1250 and allow you to carry your surf board. You can use the Rhino-Rack Crossbar Pads w/ Tie-Downs #RRRWP04. These pads will fit your HD crossbars. I…

view full answer...

Answer 7

The Dexter hub part number prefix 8-201 could refer to many items and includes many possible weight capacities. So the best way to go is to pull one hub, remove the bearings and find their stamped part numbers. If you happen to know the axle's…

view full answer...

Answer 8

I measured the widths of the c-channel on the Rhino Rack Vortex Aero Crossbars and the bottom width is 7/8 inches and the neck width is 7/16 inches. I have attached a photo showing these measurements for you to check out. As long as the t-bolts on…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Will Yakima Mighty Mount 23H Accessory Adapter Fit Factory Crossbars on a 2022 Toyota Sienna

Product Page this Question was Asked From

Continue Researching