Parts Needed To Tow a Trailer With Electric Trailer Brakes Behind a 2015 Freightliner M2
Question:
We have a 2015 M2 Freightliner that we need to add the frame trailer hitch to haul a forklift trailer BigTEx Tilt trailer payload approx. 11klbs. So we will need the frame, airline brakes and electrical for the lights too. What parts do you suggest?
asked by: Eduardo S
Helpful Expert Reply:
You will need the Curt Class V Universal Weld-on Receiver Hitch # 15902 for your 2015 Freightliner M2. This will allow you to weld on a receiver with up to 10.865" of drop. For the trailer lighting you will need a combination of the Curt Powered Tail Light Converter # C59236 and the Universal Installation Kit # ETBC7 to get to a 7-way blade trailer connector. Do note the wiring to reach the battery is 25' long so if your chassis is longer you will need additional Wire # 10-2-1 to reach the battery. Since your chassis uses air brakes you will want to use the Hayes Air Actuated Trailer Brake Controller # HA100400C to operate the electric trailer brakes on a Big Tex tilt bed trailer.
Products Referenced in This Question
Deka Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot
- Wiring
- Wire
- Jacketed Wire
- 2 Wire
- 10 Gauge
- Deka
more information >
Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Universal Fit
- 4 Flat
- CURT
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Hayes Air Actuated Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Air to Electric
- Electric over Hydraulic
- Manual Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- Indicator Lights
- Up to 360 Degrees
- Hayes
more information >
Product Page this Question was Asked From
Curt Class V Universal Weld-on Receiver Hitch and Brackets with 10.865" Drop
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 44 Inch Wide
- 1200 lbs TW
- 12000 lbs GTW
- Class V
- 2 Inch Hitch
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Trailer Hitch, Wiring, and Brake Controller for 2010 Mitsubishi Fuso FE145
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Width Of Curt Class V Trailer Hitch Receiver C15410 For 2008 Ford F-350 Super Duty With Utility Bed
- Q&A: Higher Capacity Hitch that Fits 2007 Winnebago Sightseer 29R
- Q&A: Curt Hitch # C15845 Mounting Bolt Hole Spacing
- Q&A: Mounting Flange Dimensions of Curt Hitch # 15800
- Q&A: Curt item # C15845 Dimensions
- Q&A: Curt # C15845 Dimensions - Clearance and Mounting Bolt Spacing
- Article: My Trailer Hitch Doesn't Fit
- Article: Trailer Hitch Installation Tips
- Article: Anti-Rattle Devices
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: How Level Should a Tow Bar Be When Flat Towing
- Article: Best Vehicles to Flat Tow Behind an RV