Recommended Stability Plus Stabilizer Springs for a 2012 Ford F-250 4WD

Question

Question:

Hello, Im asking about the Stability Plus Stabilizer Spring. I have a 2012 F250 Super Duty 4X4. I noticed that the 2012 4X4 is not on the list for this item, but the 2014 and up is. Is this Spring not recommended for the 2012 F250 4X4? And if not can you recommend one that is. I am hauling a Salt Dogg salt spreader in the winter and a water/fertilizer tank in the summer and the back end tends to sag pretty bad. Thank you

asked by: Markus C

0

Expert Reply:

There is a set of Stability Plus Stabilizer Springs that will work with your 2012 Ford F-250 4WD and it will definitely help with your sagging. You will want item # SPS94FR. These stabilizers have a 1,500 lbs capacity.

The Stability Plus Stabilizer Springs item # SPS34FR you were looking at, do fit your truck but only have a 900 lbs capacity.

If your salt spreader and water tank are going to be over 1,500 lbs, I recommend using the SuperSprings Custom Suspension Stabilizer and Sway Control Kit item # SSA25. This system also attaches to your leaf springs but has a 3,400 lbs capacity.

expert reply by: Jerred H

0

Answer 1

To use the Torklift Turnbuckles part #TLS9522 that you have you do not also need the #TLS9000. These kits essentially do the same thing and both would not be required.

view full answer...

Answer 2

Installing an anti-sway bar at the rear of your truck may help control some of the trailer sway, but will not prevent trailer sway from happening. Installing a sway bar helps reduce the body roll and sway you will see on the tow vehicle, but does…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 11

Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…

view full answer...

Answer 12

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Recommended Stability Plus Stabilizer Springs for a 2012 Ford F-250 4WD

Products Referenced in This Question

Featured Help Information

Instructions

Continue Researching