Parts Needed to Install Brake Controller on 2016 Ford Explorer with 4-Way

Question

Question:

2016 Ford explorer base model 4wd. Looking to pull a pop up camper. No tow package at this time. I do have a 4 wire flat connector that I wired to the rear lights. What do I need to buy to give me brake control to the camper? Thanks.

asked by: Thomas S

1

Helpful Expert Reply:

In order to use a brake controller your 2016 Ford Explorer will need to have a 7-way trailer wiring connector as the 4-way does not have ability to carry that circuit. So for that the kit you need is the part # ETBC7 which comes with a 7-way adapter and everything else needed to wire in a brake controller.

For a brake controller I really like the Redarc Tow Pro Liberty part # RED24FR and install harness # RED69FR. This puts only a small knob on your dash to control the controller instead of a larger box that can feel like it's in the way. This is also a proportional brake controller which means it senses how hard you apply the trailer brakes and applies a proportional amount of trailer braking pressure.

expert reply by: Jameson C

1

Answer 1

To install your Reese Pod brake controller in your 2018 Ford Explorer will require the install harness part #3035-P which is a confirmed fit. If you check out the 9:55 mark of the install video I attached to this page you'll see where to find the…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 6

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 7

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 8

For your 2022 Ford Explorer, I recommend the Redarc Tow-Pro Elite #RED44FR. This brake controller will provide the sleekest finish and simplest to use interface. When installed, only the control knob is left exposed keeping your interior looking…

view full answer...

Answer 9

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR for your 2023 Toyota Tacoma with the factory tow package. You will be able to connect the wiring using the Redarc Adapter #RED99FR directly to the factory connector. We also have the…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Parts Needed to Install Brake Controller on 2016 Ford Explorer with 4-Way

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching