Can L44649 Bearings Replace L44643 Bearings

Question

Question:

My trailer has a 1 inch spindle and has L44643 bearings in it currently I have a brand new set of L44649 is the ID on this bearing too big for my spindle? Thank you in advance!

asked by: Brian

0

Expert Reply:

No, the 1.063" ID # L44649 bearings cannot replace the 1.00" ID # L44643 bearings as they are too large like you mentioned; you'll need to use the # L44643.

expert reply by: Kyle S

0

Answer 1

I was unable to find the seal number you mentioned. You will need to take some measurements to make sure you get the correct replacement components. I have attached a drawing that shows where you should measure your spindle. You will also need to…

view full answer...

Answer 2

Does your trailer use roller or sealed bearings? According to Dexter Marine, who now owns TDE, the 46201 used sealed bearings. We don't carry a hub that small that uses sealed bearings, but if you could reply and provide me with the diameter…

view full answer...

Answer 3

To replace your 30372 grease seal on your 1998 Heritage Trailer, I recommend the Titan Grease Seal item #010-180-00. This has an outer diameter of 2.33 inch and an inner diameter of 1.68 inch

view full answer...

Answer 4

With the measurements you got, the closest we will have is the #AH15450ECOMP. This is an agricultural hub the uses the outer bearing #LM11949, which does match the .75", but the inner bearing does not match. This uses a #LM67048 that has a…

view full answer...

Answer 5

The best way to identify correct replacement bearings for your 19-foot single-axle Continental Tilt C715 Boat Trailer is to locate the part number on the original bearings. An alternative method is to take measurements of the spindles but this method…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Can L44649 Bearings Replace L44643 Bearings

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching