Width of Replacement Rubber Strip for Malone AirFlow2 Roof Rack Crossbars

Question

Question:

Can you tell me what the width overall this is? Also the approximate width where the indent of the left and right leg is? Thank you very much!

asked by: Zach

1

Helpful Expert Reply:

I reached out to Malone, who said the Replacement Rubber Strip for Malone AirFlow2 Roof Rack Crossbars - Bottom - 50" Long # MAL43TR is 20mm wide overall, and fits a t-slot (the indent on the left and right) that is 15mm wide.

expert reply by: Kyle S

1

Answer 1

I don't know what roof rack you have but if you are missing the strip for the crossbars that covers the channels that would be why it's whistling. If you have Rhino Rack Vortex aero bars the part #RRM626 would be what you'd need to cover…

view full answer...

Answer 2

I went out to our demo area and measured replacement strip #RRM626. It is 7/8 inches wide at the top, 1/2 inch wide at the bottom, and 3/16 inches tall overall. I have included a picture showing the dimensions for you.

view full answer...

Answer 3

I believe you are referring to the top rubber cover of your Thule AeroBlade crossbars and for that we the Replacement Cover Strip with Pattern for Thule AeroBlade Edge Cross Bars - 59" Long #TH69JH. These fit the 7501, 7501B, 7502, 7502B, 7503,…

view full answer...

Answer 4

It looks like you have the Thule Aeroblade bar. The T-slot dimensions are 1/2 inch wide for the top of the opening and 3/4 inch wide at the bottom. The T-slot is 1/8" inch tall.

view full answer...

Answer 5

I do have an option for you but the rubber strips installed into the top crossbar channel on select roof racks are specific to the crossbar. Therefore, in order for us to help you get the correct replacements we'd need to know exactly which ones…

view full answer...

Answer 6

We do have what you need, but the Replacement Rubber Strip for Thule Aero Load Bars #TH853354407 is not the correct part for the ProBars. I contacted the manufacturer regarding the correct replacement rubber strip for your Thule ProBar Evo's and…

view full answer...

Answer 7

Sure thing! What you're needing is the Replacement Vortex Strip #RRM626 which measures 15-3/4" long. Rhino-Rack unfortunately doesn't have full lengths of the strip so you have to piece this out with what you're needing. The nice…

view full answer...

Answer 8

I may have a solution for you but if you have the Model 3 roof rack by Tesla on your 2020 Tesla Model 3, then we do not have a channel cover specifically designed to fit your roof rack. If the opening in your roof rack is open then it will cause some…

view full answer...

Answer 9

Yes! The Vortex Strips in your Vortex Aero Bars #RRVA137B-2 help cut down on wind noise when driving. What I've noticed is that without the strips, it's like the bars catch some of the air and send it whistling through the C channels. What…

view full answer...

Answer 10

We do have the rubber strips for both the top and bottom of the Malone AirFlow2 crossbars. There are 3 different size bars with a top and bottom strip for each listed below. 50" Malone AirFlow2 Roof Rack #MPG215 Top Strip #MAL63TR Bottom Strip…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Width of Replacement Rubber Strip for Malone AirFlow2 Roof Rack Crossbars

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching