Dimensions of Replacement Soft Rubber Endcaps for Malone Steeltop Roof Racks

Question

Question:

Do you have exact dimensions for this end cap part?

asked by: Ken J

0

Expert Reply:

The Replacement Soft Rubber Endcaps for Malone Steeltop Roof Racks part # MAL53TR is designed for Malone SteelTop Roof Racks like part # MPG202 which have bars which measure 1-1/4" wide x 7/8" tall. Therefore, that would be the interior dimensions of the end cap in regards to bar fit.

If you need a different measurement not listed, please let me know what that is and I would be glad to see if I can provide this to you.

expert reply by: Conner L

0

Answer 1

The replacement rubber caps on the Malone SteelTop Roof Rack #MPG202 can be found as part #MAL53TR. This comes as a set of 4 so you can have some others on hand if the need arises.

view full answer...

Answer 2

We have replacement Thule square bar end caps with the part #THEC1.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Dimensions of Replacement Soft Rubber Endcaps for Malone Steeltop Roof Racks

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching