What is the Bleeder Valve Screw Size For The Redline # BP17-020 and # BP17-030

Question

Question:

My I ask what size bleeder valve screw does the BP17-020/30 take?

asked by: Chris

0

Expert Reply:

My technical contact at Redline did not have the exact size of the bleeder valve screw in the Wheel Cylinder # BP17-020, however, I found out that a 10mm wrench and socket fit the head of the screw.

In the attached video I demonstrated the fitting of the tool on the screw.

I have also attached a brief installation video of the # BP17-020 for your reference.

expert reply by: Lori W

0

Answer 1

Well we don't carry Atwood wheel cylinders so nothing we offer is going to work but I may have a better solution for you. I would recommend a 10 inch brake assembly that is free-backing like the part #AKFBBRK-35R-D for the right hand side and…

view full answer...

Answer 2

I have attached dimensioned photos with your measurements. If you need anything additional just email me back.

view full answer...

Answer 3

The replacement I recommend for an Atwood Surge Brake Actuator 85778 is the Demco Hydraulic Brake Actuator part #DM62VR. It has the same ball size, offers a bolt-on install, and has a greater capacity. The only difference is it has an electric…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

Your best route is to replace your entire surge brake assembly as Atwood no longer produces any parts for their brake actuators. The Titan Zinc-Plated Brake Actuator #T47457207K is going to be your best replacement available. It is specific to disc…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

What is the Bleeder Valve Screw Size For The Redline # BP17-020 and # BP17-030

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching