Thule Track Nut that Will Fit Channels of RetraxPro Tonneau

Question

Question:

Hi, I just purchased a Tonneau RetraxPro XR truck bed cover and need to order the correct nuts to install a Thule TK2 onto that built in track. You have two nuts listed for the TKs. Which one would be better fit for the RetraxPro XR?

asked by: Prasith B

0

Expert Reply:

The easiest to fit track nuts for the channels of your RetraxPro XR will be the track nuts part # 853-2106 due to the angle of the "square" so that would be what I would go with.

expert reply by: Jameson C

0

Answer 1

I pulled this from our warehouse and it was a lot smaller than I originally thought. In the attached picture I have all of the dimensions you requested noted. To give you a quick overview of the dimensions: Thickness - .16 inches Long Sides - .993…

view full answer...

Answer 2

Replacement Track Nut for Thule Tracker II Half Foot Pack or Tracker Fit Kits TK6, TK8, TK9 #853-2106 is made to be used with Replacement M6 x 17 mm Bolt for Thule Tracker II Half Foot Pack or Fit Kits #924-0617-15. The threading on both parts is M6…

view full answer...

Answer 3

I did some research and unfortunately Rhino-Rack does not make the HD bars #RB1800B-2 compatible with your RetraxPro tonneau cover. The only kit they make that is desinged to be used with the Retrax Pro and Retrax XR tonneau covers is the Rhino-Rack…

view full answer...

Answer 4

Racks like the Yakima OverHaul HD #Y01151-5855 and Yakima OutPost HD #Y01152-5855 are designed to fit into the T-Slots on the RetraxPRO XR Hard Tonneau Cover #RTT-80372

view full answer...

Answer 5

For the RetraxONE XR tonneau cover rails we have the Rhino Rack Vortex roof rack kit part #RRVA180B-RRRLT600 for a 71 inch long crossbar setup or the part #RRVA165B-RRRLT600. These kits come with everything you'd need to attach aero shaped bars…

view full answer...

Answer 6

Yes, if you have the older Thule non-slotted Thule load bars (square bars), they will work with the Inno Feet #INXP. As far as the a solution from Inno that will work with your Retrax XR rails like the ones on the RetraxONE XR Hard Tonneau Cover…

view full answer...

Answer 7

The RetraxONE XR Hard Tonneau Cover item #RTX57YR weighs 25 lbs. It is confirmed to fit the 6-1/2' bed length of the 2023 Chevy Silverado 1500. There are two options for Rhino-Rack crossbar kits that are compatible with the t-slots on the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Thule Track Nut that Will Fit Channels of RetraxPro Tonneau

Product Page this Question was Asked From

Continue Researching