Replacing Melted Fan Blade on Furrion RV Range Hood

Question

Question:

Previous fan blade broke off but has a nut on the motor shaft and melted plastic. Any suggestions on how to replace with new fan blade?

asked by: Jay L

0

Expert Reply:

In regards to the Furrion RV Range Hood, the correct replacement fan blade is the Replacement Fan Blade for Furrion RV 12-Volt Range Hoods part # FR63MR. In order to replace this, you'd simply need to remove the nut on the end of the shaft and swap the two out. If you have some melted plastic on the end of the shaft then you can try to heat this up before removing the nut but you may be able to remove the nut along with the plastic then just clean up any excess after. If you had melted plastic burning in the vent I'd also replace the filters, the Replacement Charcoal Filter for Furrion 12V Range Hoods part # FR43MR.

Please note, you may need to use a pair of pliers to hold the shaft while you spin the nut.

expert reply by: Conner L

0

Replacing Melted Fan Blade on Furrion RV Range Hood
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

I took a look at the owner's manual for a 2019 Chevy Blazer and on page 335 of the online manual it states "These vehicles may be dinghy towed from the front" so yes you can flat tow this vehicle! I do recommend checking out your copy…

view full answer...

Answer 3

The Kwikee 32 Series Double Step part #LC3722617 that you referenced is a replacement for the Coach step you have now. You will have to cut that wire that runs to the old module and splice it to the new module.

view full answer...

Answer 4

The replacement motor for the Greystone RV Range Hood with Light - 12V - 24" Wide - Black Item #324-000087 is the Replacement 12-Volt DC Fan Motor for Ventline RV Range Hood Item #BVD0218-00. If you also need to replace the fan blade the correct…

view full answer...

Answer 5

I have two options that will allow for you to extend the connection point between your truck and trailer. The best option for you will depending on the gross trailer weight (GTW) and tongue weight (TW) of your trailer. As long as the GTW and TW of…

view full answer...

Answer 6

We do offer a few of the "triangle" shaped shower pans. We have the #LC325246 which is 27" long and 27" wide and 10-7/8" tall. We also have the #LC209795 which is 34" long and 34" wide and has a 5" rise. Both…

view full answer...

Answer 7

The Replacement Fan Blade for Furrion RV 12-Volt Range Hoods part #FR63MR is not threaded. If you remove the nut you can pull it straight off.

view full answer...

Answer 8

I looked up the dimensions of your Sylvania Microwave SR-11092B (12-1/4" tall x 20" wide x 13" deep) and compared them to that of the Greystone Microwave part #324-000105 (12" tall x 19" wide x 14-5/8" deep). I believe…

view full answer...

Answer 9

We do not have any replacement parts for your Dometic Duo Therm 59516.531 Air Conditioner, unfortunately, however I do have another solution. Since your air conditioner is getting on the older side, It may be a good idea to think about upgrading. A…

view full answer...

Answer 10

To replace the Lippert 300-1406 motor on your RV step assembly, you will just need the Replacement Motor #LC301695. This is a direct replacement for the existing motor on your steps and will work great. I have attached a short video demonstration on…

view full answer...

Replacing Melted Fan Blade on Furrion RV Range Hood

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching