Recommended Battery Box for 2 6V Batteries Mounted on Trailer Tongue

Question

Question:

Looking for a box that will fit 2 of these. Will be mounted on tounge.

asked by: Sean J

0

Expert Reply:

For a box that will fit both of your # BRW74FR I recommend the # 329-HM484. The internal dimensions of this battery box are 21" long x 11-13/16" wide x 10-5/16" tall so you will be able to easily fit both batteries inside. This features a ventilated lid, 8 cable ports, and internal bumpers to prevent shifting and jolting.

If you would like a more secure option, the TorkLift PowerArmor # TLA7712R would also be a good choice. This features a locking lid for security as well as a heavy-gauge, brite tread diamond plate aluminum construction. It also comes with 2 battery hold-down straps and mounting hardware.

expert reply by: Robin H

0

Answer 1

I recommend the NOCO Commercial Grade battery box part #329-HM484 to hold both of the group 24 batteries. From my research a group 24- 12 volt battery measures 10.25" long x 6.8125" wide x 8.875" tall. This battery box measures…

view full answer...

Answer 2

Thanks for all of the pictures of your battery bank dimensions. Based on them the battery box part #329-HM485 would easily fit all four and would work great for you.

view full answer...

Answer 3

If you went with the Bright Way Deep Cycle Battery part #BRW74FR you'd have a 6 volt battery that is rated for 220 ah each. This appears to be double what you have now so it would be a solid upgrade.

view full answer...

Answer 4

The Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger models, #PD9260C and #PD9160A have a rated power output of 810 watts and 60 amps. The #PD9260C uses the Charge Wizard multistage charging system. Using the built-in Charge…

view full answer...

Answer 5

For a similar 60 amp converter that can charge a lithium battery you'd want the part #PD9160ALV but the part #PD9260C can only charge lead acid batteries.

view full answer...

Answer 6

The clicking sound you are getting of your coach step seemingly wanting to over extend or over retract is not a motor issue but rather a control module issue. This is basically the brains of the operation and if another item wasn't working…

view full answer...

Answer 7

If there is something causing a short it is possible that the motor could be running too long after extending or retracting and that could cause the problems. When replacing the parts make sure gears and other moving parts are properly lubricated as…

view full answer...

Answer 8

The replacement control module that you need for your 202-3207 control module on your Coach Steps is the Lippert part #LC301702 on our site. I reached out to my contact at Lippert who said this control module is the correct replacement for all of the…

view full answer...

Answer 9

You are going to need 4 of the Fulton Grease Caps #F001609. These have the 3.125" outer flange diameter.

view full answer...

Answer 10

The depth dimension of the faucet part #PF213246 that would be in a shower box like where it would be mounted is 3-1/4 inch from the back to the end of the quick disconnect or 2-5/8 inches to the top of the handles. I attached a picture of the black…

view full answer...

Answer 11

In regards to the Replacement Consumer Lockout Key for Dexter Axle Brake Actuators part #DX94FR, this is only to be used when needing to reverse with the trailer as it will stop fluid from progressing through the cylinder applying the brakes on the…

view full answer...

Recommended Battery Box for 2 6V Batteries Mounted on Trailer Tongue

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching