Replacement Remote for Jensen JWM40 and JWM41 RV Stereo

Question

Question:

Looking for a new remote for jwm41 remote

asked by: Betty J

0

Expert Reply:

The correct replacement remote for your Jensen JWM41 stereo is the Replacement Service Package # JEN94FR.

This kit works for both the Jensen # JWM40 and JWM41 models as the only difference between the 2 models is the location that it's manufactured in. I confirmed with my contact at Jensen (ASA electronics) that both models use the exact same remote.

expert reply by: Jon G

0

Answer 1

The Replacement Service Package for Jensen RV Stereo #JEN94FR contains the replacement remote you need for your Jensen JMW41 RV Stereo #JWM40. The JMW40 and JMW41 are identical but they renamed it as the JMW41 when they moved the production…

view full answer...

Answer 2

The Jensen RV Stereo #JWM40 is the same thing as the JWM41, just different item codes on our end. Most likely you will use every wire from the wiring harness, but for any wires that you don't use you can either leave them alone or use some…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Remote for Jensen JWM40 and JWM41 RV Stereo

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching