Trailer Side 7-Way Wiring Plug That is Made in the USA

Question

Question:

I’m interested in the Hopkins 7 way molded trailer connectors. Are any of them made in the USA or Canada or Europe?

asked by: Bret C

0

Expert Reply:

The Hopkins 7-Way Plug # HM20041 is made overseas (not in Europe) so for a USA made solution I recommend picking up the TorkLift Wiring Harness Extension # TLW6510 and then cutting off the socket end so you can connect that to your trailer wiring.

I recommend making your connections with heat shrink butt connectors # DW05744-10 and # DW05745-5 to protect the wiring from the elements.

expert reply by: Jon G

0

Answer 1

Dexter has confirmed that the #046-124-00 snap in grommet will work with their 7K axles.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 8

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The reverse light pin on a traditional 7-way trailer connector, like part #PK11893 or a factory connector if that's what you have on your 2018 Ram, is the center pin. Take a look at the picture I attached that shows all the pin functions. To add…

view full answer...

Answer 11

It's a wire color difference but not a function difference on the pins of the 7-way. The difference comes from the fact that the two different styles are representative of two different areas that uses trailers. Traditional is usually seen on…

view full answer...

Answer 12

The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…

view full answer...

Trailer Side 7-Way Wiring Plug That is Made in the USA

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching