Hitch Ball Recommendation for 2007 Ford Ranger with Factory Bumper
Question:
i have a 2007 ford ranger that has a place to put a hitch ball in. i need a 2 inch hitch ball with a shank that will fit in the hole that was pre built by ford
asked by: raphael
Expert Reply:
I cannot make a accurate recommendation without more information. The thickness of the bumper at the hitch ball hole and the diameter of the hole in the bumper for mounting the hitch ball will allow me to make a recommendation that will work with the bumper of your 2007 Ford Ranger.
We have 2 inch hitch balls with 3/4 inch shanks up to 3-3/8 inches long and 1 inch shanks up to 3-3/16 inches long (see link). I am sure we have a ball that will work with your bumper.
If you are planning on towing often or towing a heavy trailer you may want to consider a frame mounted receiver hitch. The Draw-Tite Max-Frame Trailer Hitch Receiver Class III, item # 75082, will fit on your Ranger and will give you the adaptability of a 2 inch receiver at the rear of the vehicle for towing, bike rack or cargo carrier.
Items needed to complete the towing setup with the hitch mentioned are listed below.
Drawbar # C45010
Pin and Clip # PC3
Hitch Ball # 19247
Hitch Lock # e98882
Products Referenced in This Question
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitch - Flush - 2-5/8" Span - Stainless Steel
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Stainless Steel
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Ideal Height for a Ball When Towing a U-Haul Trailer?
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Q&A: Should Westlake 215/75R17.5 Trailer Tire Be Inflated to Max PSI
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Wiring Diagrams
- Q&A: Can I Use Dexter Components on Lippert Axles and Vice Versa?
- Article: Trailer Hitch Balls
- Q&A: Towing Capacity for 2018 Chevy Traverse AWD
- Q&A: Comparing The Demco Autoslide And PullRite SuperGlide 5th Wheel Hitches
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Adjusting the Tension of a Reese Friction Sway Control for Weight Distribution Systems