Hitch Receiver Depth Needed For Inno Tire Hold Bike Rack

Question

Question:

Hello, I have a new 2022 Volvo XC60 with the fold away 1.25 hitch... being that it is a foldable type, I want to ensure that there is enough depth in the receiver tube to accommodate the ball mount/pin.

asked by: Andre E

0

Expert Reply:

I reached out to the manufacturer, Inno, who told me you needed 2 inches of depth behind the hitch pin hole of the hitch to use the tire hold, which is the following part number:

- Inno Tire Hold Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches # INH120

expert reply by: Kyle S

0

Answer 1

I spoke to my contact at Kuat about the problem you are experiencing and he said that while it may look like the pin holes do not line up the 3/8 inch pin that came with your Kuat Beta 1-1/4 will still fit through. When you use the #D101 you end up…

view full answer...

Answer 2

Hey Joel, we have bike racks that will work for you but the Inno bike rack part #IN25RR only fits up to 3-1/2 inch wide tires. The Kuat Piston Pro bike rack part #KU66ZR would work great as it can fit a bike tire width up to 5 inches.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Ken, so the light bar part #HLY54RR that you referenced was designed specifically to fit the Hollywood Racks Destination part #HLY66ZR but I am sure if you wanted to make it work it would be possible.

view full answer...

Answer 5

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 6

Great question Gerard! The Thule Bike Adapter Bar #TH982XT could potentially pull the seat loose, but that would take either going over some pretty rough terrain for a prolonged time, or a whole lot traveling without checking on the bike. I will say,…

view full answer...

Answer 7

Any bike rack will require some degree of lifting to seat the bike within the carrier. A hitch mounted platform type rack is definitely the right choice when being concerned about lifting height; especially if you already have a hitch installed on…

view full answer...

Answer 8

The maximum wheelbase of a bike that will fit the Inno Tire Hold 2 Bike Platform Rack - 1-1/4" and 2" Hitches - Tilting #INH120 is 48 inches.

view full answer...

Answer 9

Thanks so much for your purchase of the Inno Tire Hold 2 Bike Platform Rack #INH120. And that is a good question about how the rack is secured to your hitch, as it doesn't have a traditional hitch pin that goes all the way through, so I'll do…

view full answer...

Answer 10

I recommend using the Inno Tire Hold 2 Bike Platform Rack - 1-1/4" and 2" Hitches - Tilting #INH120, which has all of the same features of the Thule Helium 2 and the same aesthetics, plus the 60-lbs per bike capacity you're looking for.…

view full answer...

Answer 11

Between the two bike racks you mentioned I would go with the RockyMounts MonoRail part #RKY10003 over the Inno Tire Hold #INH120 because the MonoRail is lighter weight by about 15 lbs and uses a wheel clamp design that is simpler and very secure.…

view full answer...

Answer 12

On the RockyMounts SplitRail bike rack #RKY11404-4 when folded up it measures 6-1/2 inches from the center of the hitch pin hole to the closest part of the rack. If you measure the distance between the center of the hitch pin hole to the rear edge of…

view full answer...

Hitch Receiver Depth Needed For Inno Tire Hold Bike Rack

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching