Dimension From Pin Hole To End Of Shaft On Replacement Sidewind Handle # TJD-7000S-HD

Question

Question:

My crank handle was broken by an object that fell on it. It is a 1/2inch round stock. The hole the pin goes through is 2-7/16inch from center of hole to end of shaft that rides on opposite side of mount. What are the dimensions of this handle. Thanks for the help!

asked by: Chris B

0

Expert Reply:

The Replacement Sidewind Handle # TJD-7000S-HD is 2-9/16" from the center of the 3/16" roll pin hole to the end of the 1/2" shaft. It has a length of 3-13/16" from the end of the shaft to the inner side of the shaft(see image).

expert reply by: Bud M

0

Length Of Sidewind Handle # TJD-7000S-HD Shaft End
(click to enlarge)

Answer 1

Thanks for the pictures! It looks like you have a Ram side wind jack and we do sell replacement parts for it. The jack you were looking at would be a great replacement for it if these parts do are not what you are looking for. The etrailer Square…

view full answer...

Answer 2

I went to the warehouse and took a measurement of the Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks, part #TJD-7000S-HD. The handle diameter is 1/2-inch. I have attached a photo of the handle with the dimension shown you can check…

view full answer...

Answer 3

There are several different Fulton jacks that use a sidewind handle like part #F0933305S00, so to make sure we get you the correct parts, I will need a little more information about your jack. Do you know the model number of your jack? Fulton will…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Dimension From Pin Hole To End Of Shaft On Replacement Sidewind Handle # TJD-7000S-HD

Product Page this Question was Asked From

Continue Researching