What Do You Pull On To Close The Bauer European Style RV Entry Door Lock From Inside The Trailer

Question

Question:

Bauer Squeeze Latch Entry Door Lock How do you pull the door closed. I dont see anything to grab. Also will it fit my jayco 317rlok fifth wheel?

asked by: Tommy B

0

Expert Reply:

On the Bauer Products European Style RV Entry Door Lock # BA38AR you would pull on the handle that says "open" (pictured below) to close the door from the inside of your trailer.

As for fitment, you'll need to remove your current entry door lock and measure the cutout hole to determine if this is a correct fit. This lock requires a cutout hole 2-3/4" tall x 3-3/4" wide.

expert reply by: Kevin C

0

BA38AR Inner Handle
(click to enlarge)

Answer 1

The only way to know if a door handle will fit your RV is to measure the cutout and get the corresponding fit. The Bauer Products Motorhome Door Lock - Black Item #BA64FR you linked to has a required cutout dimension of 5-1/4" wide x 4-1/2"…

view full answer...

Answer 2

I recommend the Bauer Products European Style RV Entry Door Lock #BA38AR to replace your Bargman L400. As there is not a direct bolt on replacement for the Bargman L400 you will need to fabricate a panel to cover the larger hole on your door and…

view full answer...

Answer 3

That isn't a complaint that I have heard a lot of concerning the Bauer Products European Style RV Entry Door Lock #BA38AR. Finding a replacement hand rail could be a solution. I'm not sure what travel trailer you have or what hand rail set-up…

view full answer...

Answer 4

We do have an option that'll work for you! To replace your key, you are just going to need the: -Replacement Key for Bauer RV Lock #BA52RR. This is the direct replacement for your existing Bauer key number 954.

view full answer...

Answer 5

Yes it will; so long as your door is at least 1-1/2 inches thick you can use the Bauer Products European Style RV Entry Door Lock - Right Hand #BA38AR.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...