Fitment of the UWS Tool Box # UWS08297 with Roll N Lock A Series Cover on a 2019 Ford F-350

Question

Question:

Will this toolbox fit under a roll n lock A series bed cover?

asked by: Clay D

0

Expert Reply:

While we do not have the exact specs of where your Roll N Lock A series bed cover installs on/above your 2019 Ford F-350's bed rails, we do have the dimensions of the # UWS08297 to use to measure the compatibility with your cover.

Since the UWS Tool Box # UWS08297 sits on your bed, the total height of the box with the lid closed is 16-1/2" tall. As long as your Lock A series cover sits higher than 16-1/2" on your truck's bed, it can easily cover the tool box. I went ahead and attached the tool box dimensions for you to check out.

If you need the mounting hardware, that is the # UWS08353.

expert reply by: Bob C

0

UWS Tool Box # UWS08297 Dimensions
(click to enlarge)

Answer 1

The UWS Tool Box #UWS01048 does not have any fasterners or mounting hardware included or recommended for use by the manufacturer, and will typically just sit in place. The box just slides into place, but if you wanted you could source your own…

view full answer...

Answer 2

In order to find the best toolbox for your setup you'll need to do some measuring, since you have a tonneau cover you'll measure your clearance from the top of the bed to the bottom of the cover while closed and since you have a fifth wheel…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi David, Rock Tamers require an inch of space on the ball mount shank in order to mount. If the portion of the shank exposed where you'll be installing the Rock Tamers is 2" x 2" then you'll want #ERT00108, for 2.5" x…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey John, so the correct amount of spring bar tension will be based on the trailer's tongue weight and how it affects the suspension of your Nissan Frontier. Every WD system is a little different but what it comes down to typically is measuring…

view full answer...

Answer 11

There are a select few fifth wheel hitches that have replacement leg kits that would adapt them to fit the OEM prep package of your Dad's 2023 GMC Sierra 3500 but I would need to know what hitch you guys have to be able to determine if that's…

view full answer...

Answer 12

That's weird, the 7-Way Vehicle Power Adapter for Furrion RV Observation Camera #FR87PR should allow you to use your camper at the same time as that's what it's designed for. If you want to just avoid the adapter all together, I would…

view full answer...

Fitment of the UWS Tool Box # UWS08297 with Roll N Lock A Series Cover on a 2019 Ford F-350

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching