SnapPad EQ Compact Jack Pads for Equalizer Leveling Systems With 7" Foot Pad

Question

Question:

Want snap pads for 2022 class C with equalizer jacks 7” octagonal. I do have a tracing of pad if needed.

asked by: Dennis B

0

Expert Reply:

I believe what you have is the 7" square Equalizer jacks on your 2022 Class C RV(see image). This would then use the SnapPad EQ Compact Jack Pads for Equalizer Leveling Systems # SP24FR4.

If this does not match your jack, please send me any identifying numbers or images and dimensions of your jack foot plate.

expert reply by: Bud M

0

7" Square Foot Pad For Equalizer Leveling Systems
(click to enlarge)

Answer 1

Based on the information I could find you are going to need the SnapPad EQ Compact Jack Pads #SP24FR4. I have included an image you can use to verify your feet do look the same to fit these pads.

view full answer...

Answer 2

Measure the diameter of the feet of your Power Gear setup and we'll be able to determine if the #SP64FR4 is a fit. This part number is for 10 inch diameter feet which is most likely what you have. If you had 9 inch diameter feet instead…

view full answer...

Answer 3

The snap pads that you need will be determined by the size and shape of your leveling system feet. The SnapPad XTRA Jack Pads #SP54FR4 will fit 9" round feet. The SnapPad EQ Compact Jack Pads #SP24FR4 fit 7" square feet and the SnapPad EQ…

view full answer...

Answer 4

The snap pads you will need for your 2022 Winnebago Navion with 7" octagonal feet is the SnapPad EQ Compact Jack Pads for Equalizer Leveling Systems w/ 7" Square Jack Feet - Qty 4 #SP24FR4. I was able to confirm that with the manufacturer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You are correct that the kit part number 70161 that you mentioned from SnapPad is our #SP24FR4 so this would be the kit you'd need.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

To determine if your motorhome has the Tiffin air brake setup or Freightliner BrakeSync you'll need to look at the rear and see if there's an quick disconnect fitting for your air line. The standard Tiffin air coupler fitting would look like…

view full answer...

Answer 10

Great question, I did some research into the Furrion Vision S. **Furrion Vision S Wireless RV Observation Camera System w/ 3 LED Marker Light Cameras - 7" #FR98NR. You need not worry about getting any kind of upgrade or anything new to get this…

view full answer...

Answer 11

The SnapPad EQ, #SN76FR will fit 10" octagon or concave round jack feet.

view full answer...

Answer 12

Hey Dan, The ground for the Roadmaster Brake-Lite Relay Kit for Towed Vehicles #RM-88400 typically gets tied into the ground for the braking system to intertwine them so that they're active at the same time. When used to prevent turn signals from…

view full answer...

SnapPad EQ Compact Jack Pads for Equalizer Leveling Systems With 7" Foot Pad

Product Page this Question was Asked From

Continue Researching