Will the Roadmaster Rollaway Trailer Hitch Protector Work With a Gen Y Hitch

Question

Question:

Hello, will this work with a Gen Y hitch?

asked by: Michelle H

0

Expert Reply:

The Roadmaster Rollaway Trailer Hitch Protector, # RM-050 will most likely work with your hitch but you will need to take a few measurements for confirmation. You will need to measure on the center of the hitch pin hole of your Gen Y hitch to the face of the hitch. We are needing 2-7/16 inches. This designed for the support bar to seat firmly against the bottom of the hitch. If you have a gap, adjustments can be made but most hitches meet this measurement. Please see the attached product video below and follow the steps that Jeff walks through against your hitch to determine fitment.

expert reply by: Michael R

0

Answer 1

The Roadmaster Tow Dolly with Self-Steering Wheels and Electric Brakes - 4,380 lbs #RM-2000-1 has the advantage of the turning wheels as opposed to the #RM-2050-1. The turning wheels on the dolly allow the dolly and vehicle to better track with the…

view full answer...

Answer 2

The solution I would offer involves a roller unit such as the Roadmaster Rollaway Trailer Hitch Protector, part #RM-050. The Rollaway CAN be used while towing, without interfering with the ball mount or accessory.

view full answer...

Answer 3

I was able to confirm that the diameter of both the Replacement Steering Pin and Clip #RM-357100-00 and your Master Tow tow dolly are both 5/8" in diameter. You will be able to use the Roadmaster Pin on your Master Tow dolly.

view full answer...

Answer 4

The Round Cooking Rack #324-000151 has a height of 2-9/16" and a diameter of 11-15/16". Check to make sure that'll work with your microwave and if so, you're good to go!

view full answer...

Answer 5

The metal rack part #324-000151 that you referenced is 12-1/2 inches diameter like what you currently have.

view full answer...

Answer 6

The Roadmaster Rollaway Trailer Hitch Protector #RM-050 will likely work with your trailer hitch that has the tabs on the bottom of the receiver as there does not look like there is going to be any interference. So long as the tabs are completely on…

view full answer...

Answer 7

Yes, there is trimming required for the installation of the etrailer Hitch Receiver #e56RR. The trimming involves part of the underside fascia panel. I went ahead and attached a photo of the trimming area and dimensions.

view full answer...

Answer 8

We do have a trailer hitch receiver that fits your 2024 Nissan Pathfinder, from Curt. The correct part number is the following: - Curt Trailer Hitch Receiver #C46DR

view full answer...

Answer 9

Yes, there are SumoSprings that fit your 2021 Ford E-450 cutaway chassis, and what you need is the following: - SumoSprings Solo Custom Helper Springs - Rear Axle #SSR-130-54

view full answer...

Answer 10

From the sounds of your situation the Ultra-Fab Skid Wheels #UF48-979014 seem to be a great solution. Sure beats damaging your driveway. These are designed to attach to 2-1/2 inch square hitch tube on the motorhome. If you don't have this you can…

view full answer...

Answer 11

Between the two part numbers #SSR-130-54 and #SSR-130-47 the key difference is the amount of support each will provide for your 2021 Ford E-450 Class C motorhome. The 47 provides 1,500 lbs of additional support whereas the 54 provides 2,800 lbs. To…

view full answer...

Answer 12

Yes, the Rollaway Hitch Protector, #RM-050, should be plenty heavy enough to work on your 37 foot motorhome and keep the hitch from dragging when you back into your driveway, as long as the dip you have is not so deep that it is bending the hitch…

view full answer...

Will the Roadmaster Rollaway Trailer Hitch Protector Work With a Gen Y Hitch

Product Page this Question was Asked From

Continue Researching