Square Nuts For Rhino-Rack Accessory Bars On Pioneer Platform Rack

Question

Question:

Recently purchased 43137B cross bars for my pioneer rack. Would like to slide nuts in to bolt accessories to them. What nuts are required that will slide into these cross bars? The kit did only came with nuts to attach the bars to the pioneer platform.

asked by: Aaron C

0

Expert Reply:

The Replacement M6 20 mm x 20 mm x 3.5 mm Square Carac Nut for Rhino-Rack Accessories # RR29TB will fit the Rhino-Rack Accessory Bars for Pioneer Platform Rack # RR43137B that you have for your Pioneer rack.

expert reply by: Bud M

0

Answer 1

The Replacement M8 Channel Nut for Rhino-Rack Accessories #RR59TB is 1-1/4" long, 3/4" wide and 3/8" thick

view full answer...

Answer 2

It kind of depends on the accessory, but the largest channel nut that would be used is for the Eye Bolt Kit #RR43178. These channel nuts measure 2.36" long x 0.77" wide x 0.39" thick and then the diameter of the bolt itself…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 7

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 8

The Malone Universal Crossbar System #MPG201 is a more economical choice but it still does a good job. The design and quality of Thule's system is why they have such a large difference in price. Whether you go with the Thule Crossroads system…

view full answer...

Answer 9

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 10

Thanks for all the details! We definitely have a way to get a cargo basket and an awning installed on your 2024 Toyota Highlander, although the aftermarket roof rack systems will use a clamping system with your door jambs instead of mounting via…

view full answer...

Answer 11

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Square Nuts For Rhino-Rack Accessory Bars On Pioneer Platform Rack

Products Referenced in This Question

Continue Researching