Availability of Transom Saver that Can be Used with Mercury Outboard Motor

Question

Question:

Do you make a transom saver for a 400 hp Mercury?

asked by: David K

0

Expert Reply:

We have a few options for transom savers but they are not fitguided to outboard motors like you mentioned. We have the # 315-FXH which is 27-36 inches long, part # 315-FXI which is 31-40 inches long, as well as the part # 315-FXK which is 25-36 inches long. You'd need to measure your setup to see which range would fit the best.

expert reply by: Jameson C

0

Answer 1

I went out in our warehouse and measured the Tourney Transom Saver #315-FXK. The end that you would use to connect to the trailer has a 3/4" by 3/4" inner diameter. The bolt hole is centered 1/2" in from the end of the tubing. Based on…

view full answer...

Answer 2

Transom savers like the Comfort Ride Transom Saver #315-FXH are more universal design and are not made with configurations with specific boats/motors. You will want to center the transom saver on the trailer frame a close to center of the motor as…

view full answer...

Answer 3

The Tourney Transom Saver #315-FXK comes with a 2 year manufacturer's limited warranty that will cover any breakage because of faulty craftsmanship. This particular unit is made from a high quality and high strength aluminum that helps resist…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Availability of Transom Saver that Can be Used with Mercury Outboard Motor

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching