Recommendations for a Removable Weld-On Trailer Ramp Hinge

Question

Question:

Seeking weld-on hinges for a light utility trailer ramp that enable easy removal and reinstallation of the ramp.

asked by: Ken Y

0

Expert Reply:

For a weld-on hinge for your utility trailer ramp, the best option is the Butt Hinge w/ Removable Pin - 5" Long x 4-7/8" Wide - 1/2" Pin Diameter # PLR1005. This hinge comes with a removable pin which allows for you to easily mount and remove the ramp when not in use. Since the hinge has no bolt holes, it is perfect for welding applications. Each # PLR1005 comes with a single hinge, so you most likely need additional hinges for your setup depending on the dimensions of your ramp.

I went ahead and attached a demo video that walks you through some of the features.

expert reply by: Bob C

0

Answer 1

Actually the 1/2" Diameter Greasable Hinge Pin #HP12412G is not zinc coated or galvanized. It was designed to be welded so there wouldn't be an issue if you did so. It's not the prettiest weld, but I did attach a picture of…

view full answer...

Answer 2

The CE Smith Roller Bunks part #CE27710 that you referenced are made in the USA.

view full answer...

Answer 3

Yes roller bunks like the #CE27710 can be used on a V-hull boat trailer like you have. This is a very common swap done on boat trailers.

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

A 16 inch tire will not fit on a 16.5 inch wheel. You would either need to get new 16 inch wheels with the proper bolt pattern to match what the hubs require or to get your existing wheels you would need to go with 16.5 inch tires. You mentioned you…

view full answer...

Answer 12

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Recommendations for a Removable Weld-On Trailer Ramp Hinge

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching