Can Go Power Solar Flex Eclipse be Easily Added to Go Power Setup on RV

Question

Question:

hi i already have the basic system with the 100 watt panel installed on my rv. this was a factory install. Can i add this panel with the existing 100 w panel and just use the branch connectors? is that all i need to make it work?

asked by: Matt B

0

Expert Reply:

Yes, you can add the Go Power Solar Flex Eclipse Expansion Kit # GP77MR to your current setup using the included MC4 branch connectors like you mentioned.

expert reply by: Jameson C

0

Answer 1

The Go Power Solar Flex Eclipse Charging System with MPPT Solar Controller #GP67MR is a 30 amp controller. It will be 10 amps per panel so 3 panels would be the most you could hook up. You can get two of the #GP67MR and three additional panels…

view full answer...

Answer 2

The Replacement Voyager WiSight 2.0 Wireless RV Backup Camera Monitor - 4.3" Screen #ASA87FR is only compatible with 2.0 systems. Unfortunately, your WVCMS130AP is a first generation product so there are no replacement parts available. The only…

view full answer...

Answer 3

The Go Power Solar Controller part GP-PWM-30-UL is rated for up to 600 watts of solar so if you only have one 100 watt panel now, you can add up to five more of these before you max out the solar controller. The Go Power Retreat Expansion Kit part…

view full answer...

Answer 4

I believe you are asking if the Go Power Eco Solar Charging System part #34273837 has a diode in it to prevent the battery from backfeeding to the panel which it does.

view full answer...

Answer 5

The Go Power Portable Solar System with Digital Solar Controller - 200 Watt Solar Panel Item #34282610 is going to be the latest model. The kit comes with XLR-style and SAE style adapters for campers and RVs that are pre-wired for solar. If your…

view full answer...

Answer 6

For a replacement for your water heater we currently have a 6 gallon Dometic RV Water Heaters - #DMC74FR. Then you could add the Double-Panel On/Off Switch, part #AT91230, that would allow you to power the electric and gas components on and off…

view full answer...

Answer 7

I recommend going with a tankelss water heater like the Furrion RV Tankless Water Heater - Gas - Automatic Pilot - 60,000 BTU - 16" x 16" Door, part #FR98SR. This water heater comes with a 16" X 16" door, which is approximately…

view full answer...

Answer 8

For a 30-Amp service RV with the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger, #PD4045KA installed, I recommend the 1,000 Watts - 12V Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch & Remote, #PD94FR. I…

view full answer...

Answer 9

We have just what you need, the Go Power Portable Solar Panel with Digital Solar Controller, #34282610. This lets you place the solar panel where you need it for maximum sunlight while not having to place the camper in the sun too. For the later…

view full answer...

Answer 10

Yes the Mount-n-Lock GennyGo Generator and Cargo Carrier for RV Bumpers #MNT77FR that you referenced would fit on a trailer that has only 2 inches between the rear bumper and body of the trailer.

view full answer...

Answer 11

No, when adding additional panels like the Go Power Solar Flex Eclipse Expansion Kit #GP77MR in parallel, you do not need a fuse for each panel. Since the panels are connected in parallel and then go through the charge controller before reaching the…

view full answer...

Answer 12

So to answer a couple of your questions about the Go Power Solar Flex Eclipse Expansion Kit - 190 Watt Solar Panel #GP77MR: With your Super Pacific X1 having a canopy top only being a 1/2" less wide than the solar panel you have nothing to worry…

view full answer...

Can Go Power Solar Flex Eclipse be Easily Added to Go Power Setup on RV

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching