Whats the Difference Between TH05740 and TH8523387001 AcuTight Mounting System

Question

Question:

Whats the difference between TH05740 and TH8523387001?

asked by: Samuel C

0

Expert Reply:

The part # TH8523387001 is a single Acutight saddle and the part # TH05740 is a quantity of 4.

expert reply by: Jameson C

0

Answer 1

Yes, you can use replacement cradle #TH8523387001 for the Quick Grip mounting system in your Thule Atlantis 1600 cargo box. This cradle works with both the Quick Grip and AcuTight mounting systems in the current and previous generation Thule cargo…

view full answer...

Answer 2

Yes, the Replacement Tensioning Bolt Plug for Thule Traverse Foot Pack #8526446001 are designed to keep dirt and grime out of the socket used to tighten the feet.

view full answer...

Answer 3

The flat side of the Replacement Cradle for Thule AcuTight and Quick Grip Mounting Hardware part #TH8523387001 will go against the bottom of the cargo box which you can see in the attached photo. Therefore, the screw hole will be facing down…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Whats the Difference Between TH05740 and TH8523387001 AcuTight Mounting System

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching