How Wide Is The Actual Sensor For The Blind Spot Monitoring System

Question

Question:

How wide is the actual sensor? What are the specs/dimensions of the sensors

asked by: Rob D

0

Expert Reply:

After reaching out to the manufacturer The Blind Spot Monitoring System # CU95XR sensor dimensions are 4-1/2 inches x 3 inches x 1-1/2 inches.

I will attach a review video link below of the Blind Spot Monitoring System.

expert reply by: Noah E

0

Answer 1

The Replacement Breakaway System #HM39340 is the correct part for your Brake Buddy 2.

view full answer...

Answer 2

I have just what you need! For a correct braking system for flat-towing vehicles, you need a supplemental braking system instead of a brake controller. This is because brake controllers are not designed to work with flat-tow vehicles. With that…

view full answer...

Answer 3

If your current equalizer is 2" tall x 5-3/4" long, and your shackle straps are 2-1/4" long when measured from the center of one eye hole to the other, then the #K71-359-00 is going to be the kit you need. This heavy duty…

view full answer...

Answer 4

You currently have the Equa-Flex Cushioned Equalizers #LC279687 used with your Lippert axles. We do have the MORryde Rubber Equalizers #MR87ZR that you can use to replace your current equalizers. These have 3" of travel and are rated for axles…

view full answer...

Answer 5

The Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers #K71-359-00 will work on axles up to 8,000lbs.

view full answer...

Answer 6

From what I could find out about the axle you currently have, The Dexter Axle #8327872, should work. That being said, it is highly advisable to double check a few things before biting the bullet. First, this axle utilizes the inner bearing #25580 and…

view full answer...

Answer 7

From the measurements supplied, it looks like the Dexter E-Z Flex #K71-652-00 will be the best option. The equalizer will basically match your current ones and this will have both wet bolts and the ability to grease the equalizer bolt, but it is a…

view full answer...

Answer 8

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 9

Yes, that is absolutely normal and is actually mentioned in the installation instructions. To install the MORryde Safe-T-Rail Telescoping RV Hand Rail #MR54BR you're going to need to: -Remove the existing "Lend-A-Hand" rail. Once…

view full answer...

Answer 10

The awning roller that is installed on the Solera 12V Power RV Awning Conversion Kit #LC434724 that you referenced could be wound too tight and the motor can't overcome the tension. Or it's possible the battery of your RV is weak. Typically…

view full answer...

Answer 11

Everything you said is completely accurate; there's just no arguing that, so I'm really not sure what answer I can give you here that's going to be something you are satisfied with, but I'll give it a shot. In regards to the…

view full answer...

Answer 12

You can definitely shoot some self-tapping screws through the tabs of the CUB Blind Spot Monitoring System #CU94TR to ensure a tight bond along with the 3M tape. As for false readings, we haven't had any reports back stating any issues. We've…

view full answer...

How Wide Is The Actual Sensor For The Blind Spot Monitoring System

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching