Correct Ball Mounts For The Furrion Vision S Wireless RV Backup Camera System

Question

Question:

What size ball 17mm or 20mm is used to mount the 7in screen. Thanks!

asked by: Mark D

0

Expert Reply:

I checked with Furrion and the 7 inch and 5 inch monitor version of the Furrion observation system # FOS05TASF use part # FR79SR. The smaller 4.3 inch size use the part # LC776462.

The ball of the # FR79SR is 0.85" or 21.59mm and the ball of the # LC776462 is 0.60" or 15.24mm.

expert reply by: Kevin C

0

Answer 1

In regard to the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision part #FOS05TASF, the diameter of the ball on the suction cup mount (Replacement Suction Cup Mount for Furrion Vision S Wireless RV Backup Camera System part #FR79SR)…

view full answer...

Answer 2

I went out to the warehouse and measured the ball size of the Replacement Suction Cup Mount for Furrion Vision S Wireless RV Backup Camera or Observation System part #FR79SR for the 5" and 7" screens and it measures .85".

view full answer...

Answer 3

If your wheelbase is close to 35 inches like you mentioned it will work great with the MORryde Rubber Equalizers for Triple Axle Trailers #MR39ZR. This is a cushioned setup that will make a big difference the ride quality of your 2018 Grand Design…

view full answer...

Answer 4

Trailers use what is called a 2-wire system which means the turn signals and brake lights are on the same circuit. When you try to add separate amber turn signals you will need to separate out the brake light signal using a converter, #118158. On…

view full answer...

Answer 5

The Vehicle to Vehicle Tail Light Converter #C56196 that you referenced will convert a combined turn signal function to a separate one so it would work well for your 1997 Jeep Wrangler. You would only need to use one converter. I attached a picture…

view full answer...

Answer 6

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 7

Since the 15 amp plug and 30 amp plug both feed into the single 50 amp plug on Power Grip RV Power Maximizer #CAM55025 you would want both the 15 and 30 amp connections to both be single phase or 3 phase, whatever it happens to be. I suspect that if…

view full answer...

Answer 8

I reached out to Camco about the Power Grip RV Power Maximizer - 50 Amp Female to 15 Amp Male and 30 Amp Male item #CAM55025 and received this information from one of their reps. All Grounds, “G”, and all Neutrals, “W”, are connected and they should…

view full answer...

Answer 9

The 4.3 inch monitors of the Furrion Vision S camera systems have a smaller ball attachment which is why they use the mount part #LC776462. The larger 5 and 7 inch monitors use the larger ball mount #FR79SR.

view full answer...

Answer 10

Yes, the Replacement 4.3" Monitor for Furrion Vision S Wireless RV Camera System #FR77FR will work great as a replacement monitor for your Furrion FOS43TADS monitor. This monitor measures 4-3/4" wide, 3-1/8" tall, is 1" deep, and…

view full answer...

Answer 11

Thank you for the photo and what it shows is you have the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision - 5" Screen #FOS05TASF. The correct replacement suction cup is indeed the one you asked about: - Replacement Suction Cup…

view full answer...

Answer 12

I measured the ball on the Suction Cup Mount #LC776462 to be 0.629" in diameter.

view full answer...

Correct Ball Mounts For The Furrion Vision S Wireless RV Backup Camera System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching